Tennant 7400 Скачать руководство пользователя страница 64

Страница: 64 / 92

MAINTENANCE

7400 (GM) 330970 (3--05)

BATTERY

The battery for the machine is a low maintenance

battery. Do not add water to the battery, or

remove the battery vent plugs.

The battery is located under the operator seat.

After the first 50 hours of operation, and every

800 hours after that, clean and tighten the battery

connections.

FOR SAFETY: When servicing machine,

avoid contact with battery acid.

PROPELLING MOTOR

Torque the shaft nut to 508 Nm (375 ft lb)

lubricated, 644 Nm (475 ft lb) dry after the first

50-hours of operation, and every 800 hours there

after.

BELTS AND CHAINS

ENGINE BELT

The engine fan belt is driven by the engine

crankshaft pulley and drives the alternator pulley.

Proper belt tension is 13 mm (0.50 in) from a

force of 4 to 5 kg (8 to 10 lb) applied at the

mid-point of the longest span.

Check and adjust the belt tension every 100 hours

of operation.

WARNING: Moving belt and fan. Keep

away.

STATIC DRAG CHAIN

A static drag chain prevents the buildup of static

electricity in the machine. The chain is attached to

the machine frame just in front of the scrub head,

on the left side of the machine.

Make sure the chain is touching the floor at all

times.

08935

Содержание 7400





























































































Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды

Tennant 7400, Руководство оператора

Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды