Tennant 7400 Скачать руководство пользователя страница 47

Страница: 47 / 92

OPERATION

7400 (GM) 330970 (3--05)

POST-OPERATION CHECKLIST

Check the brush adjustment. See

CHECKING AND ADJUSTING SCRUB

BRUSH PATTERN

MAINTENANCE

Check for wire, string, or twine wrapped

around the scrub brushes.

Check the squeegees for wear or damage.

Drain and clean the recovery tank.

ES mode: Drain and clean the solution tank

and clean the solution outlet filter. Clean the

ES filter.

Check the vacuum hoses for debris or

obstructions.

Remove and clean the debris tray.

LPG powered machine: Check to make sure

the LPG tank service valve is closed.

Check for fuel odor that indicates a fuel leak.

Check under the machine for leak (fuel, oil,

coolant, scrubbing solution).

Check the service records to determine the

maintenance requirements.

FaST Scrubbing: If FaST PAK is empty after

scrubbing, install a new FaST PAK or

connect supply hose to the storage plug.

OPERATION ON INCLINES

Drive the machine slowly on inclines. Use the

brake pedal to control machine speed on

descending inclines. Scrub with the machine up

inclines rather then down inclines.

The maximum rated incline for scrubbing with the

machine is 6

. The maximum rated incline during

transport of the machine is 8

FOR SAFETY: When using machine, go

slow on inclines and slippery surfaces.

Содержание 7400





























































































Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды

Tennant 7400, Руководство оператора

Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды