Tennant 7400 Скачать руководство пользователя страница 52

Страница: 52 / 92

OPERATION

7400 (GM) 330970 (3--05)

Problem

Cause

Remedy

FaST System does not operate FaST switch is set for

Conventional scrubbing

Set the FaST switch for FaST

system scrubbing

FaST circuit breaker tripped

Determine cause and reset the

10A circuit breaker button

Clogged FaST PAK supply hose

and/or connector

Soak connector and hose in warm

water and clean

FaST PAK carton is empty or not

connected

Replace FaST PAK carton and/or

connect supply hose

FaST system is not primed

To prime, operate the FaST solu-

tion system for 5 to 10 minutes.

Clogged flow control orifice/screen Remove and clean orifice/screen
Faulty pump or air compressor

Contact TENNANT representative

Clogged filter screen

Drain solution tank, remove and

clean filter screen

Faulty detergent timer module

Contact Tennant representative

FaST solution flow switch is off

Turn FaST solution flow switch on

Содержание 7400





























































































Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды

Tennant 7400, Руководство оператора

Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды