Tennant 7400 Скачать руководство пользователя страница 34

Страница: 34 / 92

OPERATION

7400 (GM) 330970 (12--03)

3. Turn the ignition switch key clockwise until

the engine starts.

NOTE: Do not operate the starter motor for more

than 10 seconds at a time or after the engine has

started. Allow the starter to cool between starting

attempts or damage to the starter motor may

occur.

4. Allow the engine and hydraulic system to

warm up three to five minutes.

WARNING: Engine emits toxic gases.

Severe respiratory damage or

asphyxiation can result. Provide

adequate ventilation. Consult with your

regulatory authorities for exposure

limits. Keep engine properly tuned.

5. Release the machine parking brake.

6. Select the (Fast) engine speed with the

engine speed switch.

7. Drive the machine to the solution tank filling

area.

10896

Содержание 7400





























































































Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды

Tennant 7400, Руководство оператора

Результаты поиска

Содержание 7400

Отзывы:

Похожие инструкции для 7400

Бренды по названию

Популярные бренды