manualshive.com logo in svg

Tektronix AWG610, Руководство пользователя


Поделиться
Скачать
background image

AWG610 Arbitrary Waveform Generator User Manual

A-1

Appendix A: Specifications

This section contains theAWG610 Arbitrary Waveform Generator specifications.
All specifications are guaranteed unless labeled “typical”. Typical specifications
are provided for your convenience but are not guaranteed.

Specifications that are marked with the 

n

 symbol in the column Characteristics

are checked in Appendix B: Performance Verification and the page number
referenced to the corresponding performance verification procedures can be
found in the column PV reference page.

The characteristics in the specifications are listed in tables that are divided into
categories. In these tables, the subcategories may also appear in boldface under
the column Characteristics.

The performance limits in this specification are valid with these conditions:

H

The AWG610 Arbitrary Waveform Generator must have been calibrated/ad-
justed at an ambient temperature b20

_

 

C and +30

_

 

C.

H

The AWG610 Arbitrary Waveform Generator must be in an environment
with temperature, altitude, humidity, and vibration within the operating
limits described in these specifications.

H

The AWG610 Arbitrary Waveform Generator must have had a warm-up
period of at least 20 minutes.

H

The AWG610 Arbitrary Waveform Generator must be operating at an
ambient temperature b10

_

 

C and +40

_

 

C.

Warranted characteristics are described in terms of quantifiable performance
limits which are warranted.

Performance Conditions

Содержание AWG610



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AWG610

Caltta PH600 Quick Start Manual preview
PH600
Бренд: Caltta Страницы: 13
Fronius TransSteel 2200 Operating Instructions Manual preview
TransSteel 2200
Бренд: Fronius Страницы: 136
LawnMaster BQH3500 Safety And Operating Manual preview
BQH3500
Бренд: LawnMaster Страницы: 28
Lifetech LifeOX-AIR Ozzy User Manual preview
LifeOX-AIR Ozzy
Бренд: Lifetech Страницы: 17
iLive IPDL917 Instruction Manual preview
IPDL917
Бренд: iLive Страницы: 24
Scosche MagicMount MAGPBEZ Manual preview
MagicMount MAGPBEZ
Бренд: Scosche Страницы: 4
iDance Cube Nano cn1 User Manual preview
Cube Nano cn1
Бренд: iDance Страницы: 2
Jackery JS-100C User Manual preview
JS-100C
Бренд: Jackery Страницы: 24
Sangean DPR-17 Manual preview
DPR-17
Бренд: Sangean Страницы: 151
RAFFEL SYSTEMS ACC PS2 QU2 01 User Manual preview
ACC PS2 QU2 01
Бренд: RAFFEL SYSTEMS Страницы: 2
Pace IntelliHeat ST 115 Operation And Maintenance Manual preview
IntelliHeat ST 115
Бренд: Pace Страницы: 20
Curtis RT068 Specification Sheet preview
RT068
Бренд: Curtis Страницы: 1
Soen TRANSIT User Manual preview
TRANSIT
Бренд: Soen Страницы: 39
Yamaha EF6600D Owner'S Manual preview
EF6600D
Бренд: Yamaha Страницы: 66
Yamaha EF6300iSDE Owner'S Manual preview
EF6300iSDE
Бренд: Yamaha Страницы: 144
PISCO VJ Series Manual preview
VJ Series
Бренд: PISCO Страницы: 68
MSW MSW-PG2200 User Manual preview
MSW-PG2200
Бренд: MSW Страницы: 165
Logik L7TDVD10 Instruction Manual preview
L7TDVD10
Бренд: Logik Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды