manualshive.com logo in svg

Tektronix AWG610, Руководство пользователя


Поделиться
Скачать
background image

The Setup Menu Screen

3-44

AWG610 Arbitrary Waveform Generator User Manual

When you load or create a waveform in the waveform memory, output does not
start until you push the RUN button on the front-panel. The RUN LED is on and
the instrument starts sweeping the waveform data in the waveform memory.

When the Waveform Generator is set to the Trigger mode, the Waveform
Generator waits for a trigger event to be generated by pushing the FORCE
TRIGGER button or by external trigger event signal. Refer to The Run Mode
Menu on page 3–37.

The current run state of the instrument is displayed in the status area at the upper
part of the screen. Refer to Table 3–6 for state messages.

Table 3-6: Instrument run state and state messages 

State messages

Descriptions

Stopped

The output operation is currently stopped.

Waiting

The instrument is waiting for a trigger.

Running

The instrument is outputting waveform(s).

If waveforms are not present in any of the channels the Running or Waiting
message will be changed to the Stopped message. There will be no output when
you push the RUN button and the Stopped message will continue to be
displayed.

The RUN LED is on when the run state is Running or Waiting.

The line circuit from internal generator module to the output connector must be
closed to output waveform from the front-panel output connector.

Push the CH1 OUT button to connect or disconnect the instrument output to the
CH 1 connector. When you push the CH1 button, the CH1 LED goes on and a
waveform is output from the CH1 connector if the instrument is in the Running
state. When you push the CH1 button again, the signal output is disconnected
and the waveform output is stopped, even if the instrument is in the Running
state. If there is no waveform loaded into a channel, you cannot turn that channel
output on or off.

The CH1 LED automatically turns off when the waveform data in that channel
becomes invalid. For example, you attempt to load an incorrect file, and the
instrument deletes the current waveform from memory.

Starting and Stopping

Output

Turning Channel Output

On and Off

Содержание AWG610



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AWG610

E-Bench KH 2243 Operating Instructions Manual preview
KH 2243
Бренд: E-Bench Страницы: 37
Sun-Mate Info-Mate 837 Owner'S Manual preview
Info-Mate 837
Бренд: Sun-Mate Страницы: 14
LIPOWER G1600L User Manual preview
G1600L
Бренд: LIPOWER Страницы: 10
Onan CCK Series Instruction Manual preview
CCK Series
Бренд: Onan Страницы: 108
Wiltron 681 A Series Operation Manual preview
681 A Series
Бренд: Wiltron Страницы: 160
ayerbe AY-1000 KT Manual preview
AY-1000 KT
Бренд: ayerbe Страницы: 38
Subaru RG3200iS Instructions For Use Manual preview
RG3200iS
Бренд: Subaru Страницы: 28
Bayan Audio NEO 2 Quick Start Manual preview
NEO 2
Бренд: Bayan Audio Страницы: 12
LEXIBOOK K920 Series Instruction Manual preview
K920 Series
Бренд: LEXIBOOK Страницы: 64
Memorex MVDP1077 User Manual preview
MVDP1077
Бренд: Memorex Страницы: 41
FLO TV FLO TV PTV350 Quick Start Manual preview
FLO TV PTV350
Бренд: FLO TV Страницы: 2
Audiovox D1830 User Manual preview
D1830
Бренд: Audiovox Страницы: 39
Robin R1300 Instructions For Use Manual preview
R1300
Бренд: Robin Страницы: 32
Audiovox FR14 Operating Instructions Manual preview
FR14
Бренд: Audiovox Страницы: 6
Icom 43191510 Service Manual preview
43191510
Бренд: Icom Страницы: 90
home diesel power 7500W Owner'S Manual preview
7500W
Бренд: home diesel power Страницы: 14
home diesel power HDP-3500 Owner'S Manual preview
HDP-3500
Бренд: home diesel power Страницы: 28
MT Logic DV-1825MTB Instruction Manual preview
DV-1825MTB
Бренд: MT Logic Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды