manualshive.com logo in svg

Tektronix AWG610, Руководство пользователя


Поделиться
Скачать
background image

Appendix B: Performance Verification

AWG610 Arbitrary Waveform Generator User Manual

3. Follow the substeps below to set the AWG610 Arbitrary Waveform

Generator controls:

a. Push UTILITY (front-panel)

System (bottom)

Factory Reset

(side)

OK (side).

b. Load the MODE.WFM file.

Refer to Loading Files on page B–10 for file loading procedures.

c.

Push HORIZONTAL MENU (front-panel)

Clock (side).

d. Push 2, 0, 0 and M (SHIFT+7) keys in this order or turn the general pur-

pose knob to set the internal clock frequency to 200 MHz.

4. Push the RUN button.

The LED above the RUN button is on.

5. Verify that the clock signal amplitude is equal to or larger than 0.5 V, and the

clock signal period is 20 ns (50 MHz).

6. Disconnect the cable from the 1/4 Clock connector.

Содержание AWG610



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AWG610

JBL JBL PlayUp Instructions Manual preview
JBL PlayUp
Бренд: JBL Страницы: 11
A2Z Ozone A-7000 Operating Manual preview
A-7000
Бренд: A2Z Ozone Страницы: 13
Fender Hot Rod Deluxe Owner'S Manual preview
Hot Rod Deluxe
Бренд: Fender Страницы: 12
East Tester ET3320C User Manual preview
ET3320C
Бренд: East Tester Страницы: 16
Fresh 'N Rebel Rockbox RAW Manual preview
Rockbox RAW
Бренд: Fresh 'N Rebel Страницы: 10
Xantrex PROwatt 600 Owner'S Manual preview
PROwatt 600
Бренд: Xantrex Страницы: 36
MayPole MP3767 Manual preview
MP3767
Бренд: MayPole Страницы: 2
Champion 71001I EU Owner'S Manual & Operating Instructions preview
71001I EU
Бренд: Champion Страницы: 108
PURE Chronos CD Owner'S Manual preview
Chronos CD
Бренд: PURE Страницы: 88
Rosenbauer RS 9 Operation Manual preview
RS 9
Бренд: Rosenbauer Страницы: 84
SKF SP/SFE 30/3003 Manual preview
SP/SFE 30/3003
Бренд: SKF Страницы: 4
SKF CMAC 2504 User Manual preview
CMAC 2504
Бренд: SKF Страницы: 6
DuroStar DUAL FUEL DS4400EHF User Manual preview
DUAL FUEL DS4400EHF
Бренд: DuroStar Страницы: 66
DuroStar DUAL FUEL HYBRID ELITE DS13000EH User Manual preview
DUAL FUEL HYBRID ELITE DS13000EH
Бренд: DuroStar Страницы: 70
DUROMAX XP2000EH Operator'S Manual preview
XP2000EH
Бренд: DUROMAX Страницы: 28
DUROMAX XP4850EH-081418 User Manual preview
XP4850EH-081418
Бренд: DUROMAX Страницы: 35
Clas Ohlson 18-8039 Manual preview
18-8039
Бренд: Clas Ohlson Страницы: 44
Clas Ohlson 18-8118 Manual preview
18-8118
Бренд: Clas Ohlson Страницы: 64

Бренды по названию

Популярные бренды

Загрузить еще бренды