manualshive.com logo in svg

Tektronix AWG610, Руководство пользователя


Поделиться
Скачать
background image

Operating Basics

AWG610 Arbitrary Waveform Generator User Manual

2-11

Numeric Input

You can enter numeric values by using either the numeric keypad or the general
purpose knob. If the side menu item displays a value, you can alter this value
using the general purpose knob or numeric buttons.

Pushing the type of side menu button or selecting a parameter in a pop-up menu
causes the current setting to appear on the right end of the Status Display area as
shown in Figure 2–9.

Knob icon

Underscore

Figure 2-9: Knob icon displayed in Status Display area

A knob icon with a numeric value that includes an underscore character indicates
that you can change the value at the underscore location by using the general
purpose knob or keypad buttons. By default, the underscore character is
positioned under the digit specified depending on the parameters. You can only
change the value represented by the digits at and to the left of the underscore.
Use the 

a

 and 

'

 arrow buttons to move the underscore to the desired position,

and then turn the general purpose knob to change the value.

If the numeric value has the knob icon, but does not have the underscore, then
turning the general purpose knob cycles through a predefined set of values.

When using the general purpose knob, values you change in side menus and
menu screens take effect immediately. Values in pop-up menus are not effective
until you push the OK side button or the ENTER front-panel button.

Figure 2–10 shows the numeric keypad, with descriptions of the button
operations.

The General Purpose

Knob

The Numeric Keypad

Содержание AWG610



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AWG610

Hantek HDG3000B Series User Manual preview
HDG3000B Series
Бренд: Hantek Страницы: 102
Marathon Electric Magna Plus 280-430 Frame Installation, Operation & Maintenance Manual preview
Magna Plus 280-430 Frame
Бренд: Marathon Electric Страницы: 20
LIPOWER G1600L User Manual preview
G1600L
Бренд: LIPOWER Страницы: 10
Leader Electronics Corp. LG 3803 Instruction Manual preview
LG 3803
Бренд: Leader Electronics Corp. Страницы: 57
Tivoli Audio PAL+BT Owner'S Manual preview
PAL+BT
Бренд: Tivoli Audio Страницы: 124
Rohde & Schwarz SML01 Operating Manual preview
SML01
Бренд: Rohde & Schwarz Страницы: 299
Panasonic DVD-LS855TP Operating Instructions Manual preview
DVD-LS855TP
Бренд: Panasonic Страницы: 20
Panasonic DVD-LS82 Operating Instructions Manual preview
DVD-LS82
Бренд: Panasonic Страницы: 32
Panasonic DVD LS82 - DVD Player - 8.5 Operating Instructions Manual preview
DVD LS82 - DVD Player - 8.5
Бренд: Panasonic Страницы: 36
Panasonic DVD-L50A Operating Instructions Manual preview
DVD-L50A
Бренд: Panasonic Страницы: 58
Panasonic DVD-LS84 Operating Instructions Manual preview
DVD-LS84
Бренд: Panasonic Страницы: 108
Panasonic DVD-LS70 Operating Instructions Manual preview
DVD-LS70
Бренд: Panasonic Страницы: 112
Philips AE6570/00Z User Manual preview
AE6570/00Z
Бренд: Philips Страницы: 2
Philips AE6580 Specifications preview
AE6580
Бренд: Philips Страницы: 2
Philips AE6565/20Z User Manual preview
AE6565/20Z
Бренд: Philips Страницы: 2
Philips AE6565 User Manual preview
AE6565
Бренд: Philips Страницы: 2
Philips AE6565 Specifications preview
AE6565
Бренд: Philips Страницы: 2
Philips AE6545 Brochure preview
AE6545
Бренд: Philips Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды