manualshive.com logo in svg

Tektronix AWG610, Руководство пользователя


Поделиться
Скачать
background image

The Pattern Editor

3-82

AWG610 Arbitrary Waveform Generator User Manual

Table 3-26: Code conversion parameters (cont.)

Parameters

Description

Past Output

The portion in which you view the output data that was output first. You

 

can

view up to eight points of the conversion result of the past output.

Output Code

Writes the resulting data of conversion that is output when all the above

 

four

conditions are satisfied. Youmay specify 16 points of data.
If all conditions from Past Source to Past Output are satisfied in the

conditions portion, Output Code will be output.
Past Source, Current Source, Next Source, and Past Output are defined as

conditions segments, and Output Code as the output segment.

Operations in the dialog box can be made as follows:

A pattern must have been defined in at least one cell within a line conditions
segment on one line.

The number of points in a cell may be optional, unless it exceeds the
maximum number of points. Any blank cell is ignored during pattern
matching.

Each cell must be a pattern of 0s, 1s, and/or don’t care (minus) signs.

The maximum definable number of lines is 256 lines.

The following information explains the code conversion mechanism:

Initial state: The left end of source data is defined as the noticed point. Past
Source and Output Code data are regarded as all 0 data.

The left and right patterns to the noticed point are compared with the
individual lines of the conditions segment in the conversion table. The
comparison is from the top to the bottom to find identical lines. If such lines
are found, the Output Code data defined in the line is added to the output
data.

The noticed point shifts to the right. The amount of shift corresponds to the
size of the Current Source data that was found to identical in the source data.
The new noticed point is defined there.

The above compare process for the individual lines is repeated for the new
noticed point.

An error is caused if there are no identical lines found during the compare
process.

Refer to Appendix F:Code Conversion for code conversion examples.

Code Conversion

Mechanism

Содержание AWG610



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AWG610

Bang & Olufsen Beosound A5 User Manual preview
Beosound A5
Бренд: Bang & Olufsen Страницы: 213
National Instruments PXIe-5745 Getting Started Manual preview
PXIe-5745
Бренд: National Instruments Страницы: 16
Denver MT-777 WHITE User Manual preview
MT-777 WHITE
Бренд: Denver Страницы: 12
Muse M-335 TV User Manual preview
M-335 TV
Бренд: Muse Страницы: 14
Master Quality Power XFG2000 Owner'S Manual preview
XFG2000
Бренд: Master Quality Power Страницы: 15
Uniden PRO401HH User Manual preview
PRO401HH
Бренд: Uniden Страницы: 14
Lincoln Electric NERTAMATIC 450 Instructions For Use Manual preview
NERTAMATIC 450
Бренд: Lincoln Electric Страницы: 22
ELCOS 24082 User And Maintenance Manual preview
24082
Бренд: ELCOS Страницы: 36
Magnavox MMA3683n User Manual preview
MMA3683n
Бренд: Magnavox Страницы: 10
Magnavox MHT825 User Manual preview
MHT825
Бренд: Magnavox Страницы: 12
Panasonic RF-2200 Operating Instructions Manual preview
RF-2200
Бренд: Panasonic Страницы: 7
Panasonic RF-2900 Service Manual preview
RF-2900
Бренд: Panasonic Страницы: 18
Panasonic RF-3100 Service Manual preview
RF-3100
Бренд: Panasonic Страницы: 32
Panasonic RF-800UGA Service Manual preview
RF-800UGA
Бренд: Panasonic Страницы: 42
Panasonic DVD-LX8EE Operating Instructions Manual preview
DVD-LX8EE
Бренд: Panasonic Страницы: 33
Panasonic DVD-LX9 - Portable DVD Player Operating Instructions Manual preview
DVD-LX9 - Portable DVD Player
Бренд: Panasonic Страницы: 49
Panasonic YD-500GP5 Operating Instructions Manual preview
YD-500GP5
Бренд: Panasonic Страницы: 64
Panasonic YP-060PF Operating Instructions Manual preview
YP-060PF
Бренд: Panasonic Страницы: 72

Бренды по названию

Популярные бренды

Загрузить еще бренды