manualshive.com logo in svg

Tektronix AWG610, Руководство пользователя


Поделиться
Скачать
background image

File Management

AWG610 Arbitrary Waveform Generator User Manual

3-217

Upper Window

Lower Window

Figure 3-69: Double Windows

In Double Windows, for example, you can display the file list of the hard disk
and the one of the floppy disk, or the file list of a directory and the one of an
another directory. All of the functions that are invoked from the bottom buttons
are available except for the File function.

The most important functions used in two file lists displayed at the same time are
the Copy and Move file operations. Refer to Window Operation on page 3–217.

The windows are named as Upper and Lower windows as indicated in Fig-
ure 3–69. Select a window for operation.

Push EDIT (front) 

 Window (bottom) to display  the Window side button.

Push the Window side button again to select Double for double windows. Push
the Window side button again to select Single and to return the display back into
the signal file list.

When you display the double windows, the Select side button will be available.
Push the Select side button to select Upper for file operation in the upper file list
window. Push the Select side button again to select Lower for file operation in
the lower file list window.

The most useful functions to be used in the double windows may be those
invoked from the File bottom button. The functions available in the File bottom
button are described in Table 3–52.

Window Operation

Operation in Double

Windows

Содержание AWG610



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AWG610

Caltta PH600 Quick Start Manual preview
PH600
Бренд: Caltta Страницы: 13
Jackery Explorer 1000 Pro User Manual preview
Explorer 1000 Pro
Бренд: Jackery Страницы: 40
Hantek HDG3000B Series User Manual preview
HDG3000B Series
Бренд: Hantek Страницы: 102
Vector ElectroMate VEC095 Owner'S Manual & Warranty preview
ElectroMate VEC095
Бренд: Vector Страницы: 20
Feider Machines FGHi3500 Original Instructions Manual preview
FGHi3500
Бренд: Feider Machines Страницы: 26
PowerLand PDL4000 Manual preview
PDL4000
Бренд: PowerLand Страницы: 29
Uniden PRO401HH User Manual preview
PRO401HH
Бренд: Uniden Страницы: 14
Sangean Sangean- RCR-3 User Manual preview
Sangean- RCR-3
Бренд: Sangean Страницы: 24
morse GCRS-40-40 T4F Product Manual preview
GCRS-40-40 T4F
Бренд: morse Страницы: 34
Icom IC-F3022S Instruction Manual preview
IC-F3022S
Бренд: Icom Страницы: 32
Icom IC-A25C User Manual preview
IC-A25C
Бренд: Icom Страницы: 53
Sven PS-280 User Manual preview
PS-280
Бренд: Sven Страницы: 16
Ayce 1337559 Operator'S Manual preview
1337559
Бренд: Ayce Страницы: 61
DuroStar DS13000E User Manual preview
DS13000E
Бренд: DuroStar Страницы: 66
DUROMAX XP85000E User Manual preview
XP85000E
Бренд: DUROMAX Страницы: 74
DUROMAX XP5500E User Manual preview
XP5500E
Бренд: DUROMAX Страницы: 76
DUROMAX XP13000HXT User Manual preview
XP13000HXT
Бренд: DUROMAX Страницы: 82
Chicago Electric 91213 Operating Instructions Manual preview
91213
Бренд: Chicago Electric Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды