manualshive.com logo in svg

Tektronix AWG610, Руководство пользователя


Поделиться
Скачать
background image

Quick Editing

3-96

AWG610 Arbitrary Waveform Generator User Manual

Setting Parameters

When changes are made to the waveform by turning a knob, the values of the
shifted points are calculated by interpolation. You can select either Linear or
Quadratic for the interpolating method.

Press the Interpolation side button to toggle between Linear or Quadratic.

When changes are made to the waveform by turning a knob, the shifted points
and the points in the nonshifted area are linked smoothly. This is called
smoothing. This parameter specifies the extent (of the nonshifted points) to
which smoothing applies. The value may be 0 to 1000.

1. Press the Smoothing side button.

2. Use the general purpose knob or numeric keys for value.

This specifies the center used for vertical scaling. The value may be –1.0 to 1.0.

1. Press the Vertical Origin side button.

2. Use the general purpose knob or numeric keys to change the value.

Moving the Cursor

During execution of Quick Edit, you can change the target area for editing, by
moving the cursors. When you use one of the four VERTICAL/HORIZONTAL
knobs; the general purpose knob and the numeric keys remain assigned to change
the value. To move a cursor, press the TOGGLE button on the front-panel before
operating the general purpose knob or numeric keys.

Follow the steps below to move the cursor:

1. Press the TOGGLE button on the front-panel to assign the general purpose

knob to cursor movement.

2. Set the cursor position using the general purpose knob or numeric keys.

Interpolating Method

Range of Smoothing

Position of Center of

Vertical Extent

Содержание AWG610



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AWG610

bem wireless HL2022A User Manual preview
HL2022A
Бренд: bem wireless Страницы: 5
Polaroid PDM-0743LA Operation Manual preview
PDM-0743LA
Бренд: Polaroid Страницы: 40
ULTTY SKJ-CRS01 Instruction Manual preview
SKJ-CRS01
Бренд: ULTTY Страницы: 60
Wen 56310i Manual preview
56310i
Бренд: Wen Страницы: 40
Soga PMG 112 Use And Maintenance Manual preview
PMG 112
Бренд: Soga Страницы: 28
AWA T2102B User Manual preview
T2102B
Бренд: AWA Страницы: 37
LOTRONIC 10-5699PLS User Manual preview
10-5699PLS
Бренд: LOTRONIC Страницы: 20
Medion E66050 Manual preview
E66050
Бренд: Medion Страницы: 194
Magnasonic MDVP455 Instruction Manual preview
MDVP455
Бренд: Magnasonic Страницы: 4
Papa Protect Qube BT6010 Owner'S Manual preview
Qube BT6010
Бренд: Papa Protect Страницы: 18
Venturer PVS6370 Owner'S Manual preview
PVS6370
Бренд: Venturer Страницы: 2
Venturer PVS3389 Owner'S Manual preview
PVS3389
Бренд: Venturer Страницы: 2
Venturer PVD730 Owner'S Manual preview
PVD730
Бренд: Venturer Страницы: 1
DMTech DAB14 Manual preview
DAB14
Бренд: DMTech Страницы: 52
Hobart 140GT17K Operation And Maintenance Manual With Illustrated Parts List preview
140GT17K
Бренд: Hobart Страницы: 186
TOOLCRAFT 2612922 Operating Instructions Manual preview
2612922
Бренд: TOOLCRAFT Страницы: 58
Dual 16-3267 Operating Instructions Manual preview
16-3267
Бренд: Dual Страницы: 25
Virtual Reality VRPD7 User Manual preview
VRPD7
Бренд: Virtual Reality Страницы: 37

Бренды по названию

Популярные бренды

Загрузить еще бренды