manualshive.com logo in svg

Tektronix AWG610, Руководство пользователя


Поделиться
Скачать
background image

Capturing Waveforms

3-172

AWG610 Arbitrary Waveform Generator User Manual

Procedures for Capturing Waveforms

Do the following steps to capture a waveform:

1. Set the GPIB parameters in the AWG610 Arbitrary Waveform Generator.

The AWG610 Arbitrary Waveform Generator must be set to the controller.
Refer to Connecting to a GPIB Network on page 3–153 for setting the GPIB
parameters.

2. Set the GPIB address and Talk/Listen mode in the source instrument.

3. Start acquisition in the source instrument.

Do the following steps to capture the waveform:

1. Push EDIT (front-panel)

Tools (bottom)

Capture Waveform (side).

The dialog box listing the instruments appears as shown in Figure 3–57.

Figure 3-57: Source instrument selection dialog box

a. If necessary, select Others... to open the other source instrument list.

The dialog box listing the instruments appears as shown in Figure 3–58.

b. Select a source instrument from the list.

c.

Push the OK side button.

Содержание AWG610



















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AWG610

GE AF-650 GP Series Operating Instructions Manual preview
AF-650 GP Series
Бренд: GE Страницы: 138
Logik LCRAD14 Instruction Manual preview
LCRAD14
Бренд: Logik Страницы: 2
Grundig G4 WORLD RECORDER Owner'S Manual preview
G4 WORLD RECORDER
Бренд: Grundig Страницы: 84
RDL STICK-ON ST-RG1 Quick Start Manual preview
STICK-ON ST-RG1
Бренд: RDL Страницы: 2
Harbor Freight Tools Predator 63966 User Manual preview
Predator 63966
Бренд: Harbor Freight Tools Страницы: 20
Philips PET741T Specifications preview
PET741T
Бренд: Philips Страницы: 2
Philips PET741R Specifications preview
PET741R
Бренд: Philips Страницы: 2
Philips PET741P Specifications preview
PET741P
Бренд: Philips Страницы: 2
Philips PET741N Specifications preview
PET741N
Бренд: Philips Страницы: 2
Philips PET741D/12 User Manual preview
PET741D/12
Бренд: Philips Страницы: 20
Philips PET741D User Manual preview
PET741D
Бренд: Philips Страницы: 21
Philips PET741M User Manual preview
PET741M
Бренд: Philips Страницы: 24
DUROMAX XP85000E User Manual preview
XP85000E
Бренд: DUROMAX Страницы: 74
DUROMAX XP5500E User Manual preview
XP5500E
Бренд: DUROMAX Страницы: 76
DUROMAX XP13000HXT User Manual preview
XP13000HXT
Бренд: DUROMAX Страницы: 82
Chicago Electric 45416 Assembly and Assembly And Operating Instructions Manual preview
45416 Assembly and
Бренд: Chicago Electric Страницы: 11
Honda EM3500SX Owner'S Manual preview
EM3500SX
Бренд: Honda Страницы: 63
GoVideo DP8440 Features preview
DP8440
Бренд: GoVideo Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды