Tekron TCG 01-G страница 33 Скачать руководство пользователя | Manualshive

Страница: 33 / 52

background image

TEK-TCG 01-G-Manual-v6-052021

P a g e

| 33

www.tekron.com

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The

information in this document is provided for informational use only and is subject to change. For further information or support,
go to www.tekron.com.

FACTORY HARDWARE OPTIONS

for further information).

Varistor protection and current limiting (nominally 5 mA) are employed for protection on the

general-purpose input.

Figure 12 – TCG 01-G isolation zones

Transformer isolation via a DC-DC converter is used for the main power supply and for power to
each of the logic output-drive circuits. The serial communications interface is also separately

powered via the isolating DC-DC converter.
High-speed, fixed delay opto-isolators are used in each of the time-sensitive signaling paths.

The isolation does not degrade the time accuracy of the output signals, as the fixed delays of
the isolating components (together with the delay associated with the antenna lead-in) are all
internally compensated.

«
...
31
32
33
34
35
...
»

Содержание TCG 01-G





















































Отзывы:

Нет отзывов

Похожие инструкции для TCG 01-G

Бренд: 3onedata Страницы: 3

Бренд: Peak Страницы: 8

Бренд: Growatt Страницы: 45

Бренд: StarTech.com Страницы: 3

Бренд: INVT Страницы: 156

Бренд: M-Audio Страницы: 2

ATLONA AT-HDVS-RX

Бренд: Panduit Страницы: 2

Бренд: OLIJU Страницы: 20

SUNNY BOY STORAGE 3.7

Бренд: SMA Страницы: 142

Бренд: Santerno Страницы: 156

JUXTA VJP8 Series

Бренд: YOKOGAWA Страницы: 6

SUNNY BOY 3600TL

Бренд: SMA Страницы: 2

CTRLink EIMK-100T/FT

Бренд: Contemporary Controls Страницы: 4

Бренд: Joy-it Страницы: 4

CineCast 2000-0422

Бренд: Vela Страницы: 196

Бренд: M-system Страницы: 2

PMH-24V50WCA Series

Бренд: Delta Страницы: 2

Бренд: Seller Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды