Tekron TCG 01-G Скачать руководство пользователя страница 16

Страница: 16 / 52

TEK-TCG 01-G-Manual-v6-052021

P a g e

| 16

www.tekron.com

information in this document is provided for informational use only and is subject to change. For further information or support,

go to www.tekron.com.

P2, P3: Programmable Outputs (2-pin [3.81 mm] / BNC or ST Fiber)

Electrical and Physical Configuration

Each output port may be fitted at the factory according to the following:

Electrical

Electrical Specification

Physical

TTL

CMOS/TTL (5 V) logic level driver output ports, 150 mA sink and
source. The port is fully floating and has independent electrical

isolation to 2.5 kV.

2-pin
or BNC

RS422

High Speed RS422/485 (5 V differential) output ports. The port

is fully floating and has independent electrical isolation rated
to 2.5 kV.

2-pin

HV MOSFET

Power MOSFET Switch, allowing switching of 300 VA, 100 mA
max. The port is fully floating and has independent electrical
isolation rated to 2.5 kV. Refer to Figure 11 for the suggested
wiring configurations for use with Power MOSFET switching.

2-pin

Fiber

ST fiber transmitters, compatible with ST-terminated multi-
mode fiber optic cabling. (λ=820 nm)

ST Fiber

Examples of the three connector types are given in (

Figure 6

) to (

Figure 8

);

Figure 6 – 2-pin connector

Figure 7 – BNC connector

Figure 8 – Fiber connector

If an output is not being used, it may be left unconnected. The dust cap should remain in place
on unused fiber connectors.

P2, P3 Programmable Output Options

The user may configure

and

to output in either inverted or non-inverted polarity:



A configurable number of pulses per second, minute, hour, or day with adjustable pulse
width and offset.



IRIG-B time code (unmodulated DCLS or modified Manchester) with optional IEEE
C37.118.1 or AFNOR NF S87-500 extensions.



Simulated DCF77 receiver time code.

Refer to the Tekron Configuration Tool Manual for further information.

Содержание TCG 01-G




















































Результаты поиска

Содержание TCG 01-G

Отзывы:

Tekron TCG 01-G, Руководство пользователя, Страница: 16 / 52

Результаты поиска

Содержание TCG 01-G

Отзывы: