manualshive.com logo in svg

Tekron TCG 01-G, Руководство пользователя

Поделиться
Скачать
Tekron TCG 01-G Скачать руководство пользователя страница 7

TEK-TCG 01-G-Manual-v6-052021 

P a g e

 | 7 

www.tekron.com 

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The 

information in this document is provided for informational use only and is subject to change. For further information or support, 
go to www.tekron.com.

 

2.

 

FRONT PANEL 

 

Figure 2 – TCG 01-G front panel 

TCG 01-G features two LED indicators on the front panel (Figure 2), together with a 2-line by 16-

character backlit LCD display. 

SYN LED: 

This LED shows the status of the current sync source. 

ALM LED: 

This LED shows the alarm status of the TCG 01-G. 

LCD Display 

On initial power-up, the LCD display shows a copyright message, along with the serial number 
and firmware version of the unit. See 3 - Start Up (Clock ID).  
After power-up, if the TCG 01-G is configured to operate in its default mode (GNSS 
synchronized), the display changes automatically to indicate that it is waiting for satellites 
(Figure 4). 
Once one or more satellites have been discovered, it transitions to the operating default display 
(Figure 5). 
Figures 6 and 7 show alternative time displays that the user can access by pressing the button 
on the front panel between the LED indicators. Successive button presses can be used to cycle 
through all the display screens in turn. Examples of the display screens are shown below. 

Содержание TCG 01-G





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды