manualshive.com logo in svg

Tekron TCG 01-G, Руководство пользователя


Поделиться
Скачать
background image

TEK-TCG 01-G-Manual-v6-052021 

P a g e

 | 29 

www.tekron.com 

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The 

information in this document is provided for informational use only and is subject to change. For further information or support, 
go to www.tekron.com.

 

on the coaxial cable, the impulse suppressor activates, short-circuiting the cable directly to the 
protection ground. 

While the Lightning Protector kit provides a high degree of protection, there is no 
guarantee of protection against ALL surge related events, including a direct lightning 
strike to the antenna. Careful antenna positioning is strongly advised! 

The performance of the antenna system under normal (non-surge) conditions is unaffected by 
the introduction of a correctly installed Lightning Protector. 

Installation 

The impulse suppressor should be installed as per the instructions provided with the impulse 
suppressor. 

Disclaimer 

TEKRON INTERNATIONAL disclaims any liability or responsibility for the results of improper or 

unsafe installation practice including, but not limited to, any excessive performance 
degradation of the antenna system resulting from incorrect field installation of coaxial cable 
connectors. 

Содержание TCG 01-G





















































Отзывы:

Нет отзывов

Похожие инструкции для TCG 01-G

Peak Genius 1022 Installation Manual preview
Genius 1022
Бренд: Peak Страницы: 8
Wagan 5000W AC Power Inverter User Manual preview
5000W AC Power Inverter
Бренд: Wagan Страницы: 11
Autopilot APCG4LP Manual preview
APCG4LP
Бренд: Autopilot Страницы: 13
B&R SDL4 User Manual preview
SDL4
Бренд: B&R Страницы: 45
Mosa GE 35 PS Use And Maintenance Manual preview
GE 35 PS
Бренд: Mosa Страницы: 48
Volt Polska SINUSPRO-800S User Manual preview
SINUSPRO-800S
Бренд: Volt Polska Страницы: 5
Pro-Ject Audio Systems DAC Box E Instructions For Use preview
DAC Box E
Бренд: Pro-Ject Audio Systems Страницы: 3
C2G TRUlink 81667 User Manual preview
TRUlink 81667
Бренд: C2G Страницы: 263
SIIG CE-H26E11-S1 User Manual preview
CE-H26E11-S1
Бренд: SIIG Страницы: 32
Hall Research Technologies SP-HD-4A User Manual preview
SP-HD-4A
Бренд: Hall Research Technologies Страницы: 8
leadsun AE3 Series User Manual preview
AE3 Series
Бренд: leadsun Страницы: 8
La Boite Concept LP160 User Manual preview
LP160
Бренд: La Boite Concept Страницы: 52
Velleman HQ-Power HQDB10001 User Manual preview
HQ-Power HQDB10001
Бренд: Velleman Страницы: 53
Esu LokPilot Fx micro V3.0 User Manual preview
LokPilot Fx micro V3.0
Бренд: Esu Страницы: 72
Contemporary Controls CTRLink EIMK-100T/FT Installation Manual preview
CTRLink EIMK-100T/FT
Бренд: Contemporary Controls Страницы: 4
MiLAN MIL-C2414 Series Installation Manual preview
MIL-C2414 Series
Бренд: MiLAN Страницы: 4
Navico NSPL-500 User Manual preview
NSPL-500
Бренд: Navico Страницы: 24
Zeversolar Zeverlution 1000S Quick Installation Manual preview
Zeverlution 1000S
Бренд: Zeversolar Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды