Tekron TCG 01-G страница 13 Скачать руководство пользователя | Manualshive

Страница: 13 / 52

background image

TEK-TCG 01-G-Manual-v6-052021

P a g e

| 13

www.tekron.com

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The

information in this document is provided for informational use only and is subject to change. For further information or support,
go to www.tekron.com.

3.

BACK PANEL

An example TCG 01-G back panel is shown in Figure 5 below. Its appearance may vary, as
different connector types can be fitted at the factory to suit your requirements.

Figure 5 – Rear panel of TCG 01-G, configured with 2-pin connectors (P2 and P3)

P1: Power Input (2-pin Connector [5.08 mm])

Power is applied to the unit via this plug. Maximum steady state power

consumption is 6 W, and surge protection is provided. A mating connector is
supplied that is suitable for wiring up to 1.5 mm

2

.

The polarity of the DC power source is not important as both the unit and case are

isolated from the supply input.

Check the label on the base or side of the unit for the power supply voltage rating
before powering the unit.
A 5 A fuse of appropriate voltage rating should be fitted into the non-earthed power

supply line.
NOTE: The fuse working voltage should be greater than the supply voltage.

Earth Stud (M4 Nut)

Located under the serial port, to the left of the P4 designator is a M4 bolt
provided for earthing. An external ground connection must be connected to

ensure appropriate grounding for the unit. This provides a safe discharge path in

the event of a short circuit or high voltage transient.

«
...
11
12
13
14
15
...
»

Содержание TCG 01-G





















































Отзывы:

Нет отзывов

Похожие инструкции для TCG 01-G

Бренд: S.M.S.L Страницы: 16

Бренд: Vanner Страницы: 44

AZZUPRO 5-20-ZSS

Бренд: ZCS Страницы: 44

Бренд: ORO Страницы: 18

Бренд: ICP DAS USA Страницы: 43

Бренд: W&T Страницы: 12

Бренд: BSPH Страницы: 36

Бренд: Votek Страницы: 33

Бренд: Velleman Страницы: 11

Бренд: Kaco Страницы: 42

Бренд: Climax Страницы: 2

Бренд: ADF Web Страницы: 24

Бренд: Epever Страницы: 24

Бренд: Black Box Страницы: 18

Бренд: Quantum Harvest Страницы: 33

Бренд: Clayton Power Страницы: 12

Бренд: Haier Страницы: 54

Бренд: Haier Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды