Tekron TCG 01-G Скачать руководство пользователя страница 42

Страница: 42 / 52

TEK-TCG 01-G-Manual-v6-052021

P a g e

| 42

www.tekron.com

information in this document is provided for informational use only and is subject to change. For further information or support,
go to www.tekron.com.

String-G Time Code O/P on P4

About

This general time string is used predominantly in Europe.

Timing

The string is transmitted once every second, with the leading edge of the
“start” bit of the last <ETX> exactly on the second.

Comms

9600bps, 8-bit ASCII, no parity

Definition

<STX>swhhmmssddMMyy<LF><CR> <ETX>

Placeholder

Content

<STX>

Start of Text: HEX 02

Clock Status (see below)

Day of Week (see below)

hour of day: “00” – “23”

minute of day: “00” – “60”

seconds: “00” – “59”

day of month: “01” – “31”

month of year: “01” – “12”

year: “10” – “99”

Carriage Return Line Feed Pair: HEX 0D 0A

<ETX>

End of Text: HEX 03

LOCK

TATUS

The s “Clock Status” is an ASCII character in the range 0-9, A-F representing a single hex digit
(nibble)
Bits: 3

No announcement for time change

Announcement for time change – active for an hour

before
X

Local Standard Time (LST)

Daylight Saving Time (DST)

Time/date invalid – clock is out of sync

Hold-over mode – running on local Oscillator

GNSS / IRIGB controlled mode

GNSS / IRIGB controlled mode (high accuracy)

Содержание TCG 01-G




















































Результаты поиска

Содержание TCG 01-G

Отзывы:

Бренды по названию

Популярные бренды

Tekron TCG 01-G, Руководство пользователя

Результаты поиска

Содержание TCG 01-G

Отзывы:

Бренды по названию

Популярные бренды