manualshive.com logo in svg

Tekron TCG 01-G, Руководство пользователя

Поделиться
Скачать
Tekron TCG 01-G Скачать руководство пользователя страница 11

TEK-TCG 01-G-Manual-v6-052021 

P a g e

 | 11 

www.tekron.com 

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The 

information in this document is provided for informational use only and is subject to change. For further information or support, 
go to www.tekron.com.

 

LED Indicators 

The 

SYN LED

 shows the status of the sync source. The various states are as follows: 

State 

Description 

off 

The TCG 01-G has no power. 

on 

The TCG 01-G is synchronized to the source indicated by the LCD 
display. 

Slow Flash (1 per second)  The TCG 01-G is operating in the “holdover” state (holdover timer 

running) 

Fast Flash (5 per second)  The TCG 01-G is not synchronized. “Out of Sync” condition. 

Table 3 – SYN LED 

 
The 

ALM LED

 indicates the internal alarm status of the TCG01-G. It has only two operating 

states:- 

State 

Description 

off 

The TCG 01-G is operating normally. i.e., there are no alarms. 

Fast Flash (5 per second) 

Alarms are active. In this case, the actual alarm state is shown on the 

top line of the LCD display, replacing the normal date information 
(see example in Figure 8 above). 

Table 4 – ALM LED 

 

 

 

Содержание TCG 01-G





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды