Tekron TCG 01-G страница 26 Скачать руководство пользователя | Manualshive

Страница: 26 / 52

background image

TEK-TCG 01-G-Manual-v6-052021

P a g e

| 26

www.tekron.com

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The

information in this document is provided for informational use only and is subject to change. For further information or support,
go to www.tekron.com.

7.

FACTORY RESET

The TCG 01-G features the ability to reset to factory default settings in the event that the

administrator password is forgotten, or if the clock is rendered unreachable on the network due
to incorrect settings, provided that physical access to the unit is available.

This feature is disabled by default in order to maximize security and must be enabled via the
Tekron Configuration Tool before it can be used. When disabled, there is no method to gain full

access to the unit without the administrator password, and if the administrator password is
forgotten, the unit must be returned to Tekron for reprogramming at the customer’s expense.

This feature may be permanently disabled on the unit by Tekron on request.

For further details on this feature, see the Configuration Tool Manual, which can be downloaded
from the Tekron website at

(www.tekron.com/downloads)

«
...
24
25
26
27
28
...
»

Содержание TCG 01-G





















































Отзывы:

Нет отзывов

Похожие инструкции для TCG 01-G

Бренд: Samson Страницы: 44

Бренд: TANDBERG Страницы: 384

E5714 DSNG Voyager

Бренд: TANDBERG Страницы: 314

Бренд: Broadcast Tools Страницы: 10

Бренд: Seneca Страницы: 4

Бренд: Allied Telesis Страницы: 50

DataBender CVX-1300

Бренд: Cypress Страницы: 28

Бренд: Mosa Страницы: 48

Factory-Link-SPE-M

Бренд: I-novative Страницы: 12

Бренд: T+A Elektroakustik Страницы: 60

Бренд: Sonnen Страницы: 5

Бренд: Kostal Страницы: 12

Бренд: Daihen Страницы: 158

Бренд: Xnexus Страницы: 20

Бренд: B PLUS TV Страницы: 10

Бренд: SHOWTEC Страницы: 16

Бренд: Liros Страницы: 3

Бренд: SMA Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды