manualshive.com logo in svg

Tekron TCG 01-G, Руководство пользователя

Поделиться
Скачать
Tekron TCG 01-G Скачать руководство пользователя страница 23

TEK-TCG 01-G-Manual-v6-052021 

P a g e

 | 23 

www.tekron.com 

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The 

information in this document is provided for informational use only and is subject to change. For further information or support, 
go to www.tekron.com.

 

synchronize to the GNSS source, then it will spend an additional 30 seconds at most validating 
that the sync source is stable before reporting that it is ‘in sync’. The TCG 01-G performs 
stability validation on all incoming sync sources before reporting that it is ‘in sync’. 
Reactivating a unit that was previously synchronized thousands of kilometers away from the 
present position will take longer but not more than 45 minutes. 
As described in LCD Display, the button on the front panel will toggle the display on the LCD and 
can also enter the Contrast Adjustment Mode.  
Once powered up, the operator can determine correct operation of the TCG 01-G by observing 
the LEDs. The ALM LED should be off and the SYN LED should be continuously on. If the LEDs 
are flashing, refer to the  

 

Содержание TCG 01-G





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды