I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO
7
Operator's guide
CONNECTION TO THE WATER SUPPLY
1.
2
3.
CONNECTION TO THE MAINS
1
Level alarm buzzer N.B. the gearmotor block activates the acoustic alarm but does not stop the
refrigerating unit, which must be switched off immediately
INTERNAL CLEANING
1
2
3
4
5
6.
WATER LEVEL TANK FISHING
1.
2.
3
4
FISHING
model
models
One end of the water supply pipe, which is situated inside the tank, must be screwed onto the solenoid
valve, and the other end connected to the water supply (A). . One end of the drainage pipe must be
connected to the appliance coupling using a clamp, and the other end to a standard water drain (B).
The mains water should be drinkable, and preferably purified (see picture 9).
. Ensure that mains vol
. Switch off the electrical. . Remove goods and store in another suitably refrigerated place kept at the
same temperature. . Remove the ice from the bottom of the tank. . Remove the plug from the bottom of
the tank . Wipe walls and accessories with a soft sponge dipped in water and a little baking soda.
Carefully dry everything and return everything to its initial position before starting up the appliance
once again.
Switch off the electrical.
Remove the protection grille placed on the back of the appliance.
. Periodically (depending on the hardness of the water) empty the tank of water and fill with a de-scaling
detergent, leaving to soak as indicated on the product package, then rinse well, making the unit run to
remove the ice produced until the product used has been completely eliminated. . Replace everything in
reverse order (See picture 7).
tage and frequency are the same as those stated on the rating plate (A) attached
to the appliance (see picture 3). . Ensure that the supply socket:
. Ensure that there is no danger of explosion (AD) in the room. . Make sure the environment
is suitable for the power supply cable provided. The cable of the appliance is H05 VVF, designed for
internal use. . Insert the plug in the socket (do not use three-way adapters and reduction adapters).
if the equipment has been transported or stored overturned, let is rest in its correct position for at
least 3 hours before hooking it up to the mains.
(see picture 2)
The equipment controls are located in the control panel:
Use to connect the cooling system
Use to switch on the light
Use to switch on the light and raise the hood
Before placing goods ensure that:
the plug is connected;
the refrigeration unit switch is on (green light lit up); . thermometer shows the
desired temperature for the goods to be stored; . appliance is not exposed to direct sunlight or to
powerful lamps;
ambient temperature does not 30°C with 55% R.H. (climatic class 4);
. Open the cover. . Switch off the appliance.
Remove the screws securing one of the lamp sockets in
place. . Remove the lamp socket, whilst holding the fluorescent tube and its protective cover. . Pull the
protective cover out of the other lamp socket. . Replace the fluorescent tube. . Refit all components by
following the above instructions in reverse order (see picture 6).
2
3
4
5
N.B.:
OPERATIONS AND ADJUSTMENT
(1)
(2) Refrigeration switch:
(3) Light switch:
(4) Light-lift switch:
(5) Plug
CAUTION:
1.
2.
3
4
5.
REPLACEMENT OF THE LAMP
1
2
3.
4
5
6
7
a)
b)
c)
is properly earthed;
fulfils the
requirements of the rated current as set out on the rating plate;
complies with the IEC regulations:-
thermal-magnetic switch with In = rated value as stated on the rating plate; - differential with Id sensitivity
= 30 mA.
!
10.
8.
7.
9.
11.
12.
