I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO
6
Operator's guide
Operator's guide
npacking instructions
lass assembly
pening the protective cover
Cleaning of the internal tank
leaning the cover and external parts
rip trays
onnection to the water supply
onnection to the mains
9) perations and adjustment
:
1)U
2)G
3)O
4)
5)C
6)D
7)C
8)C
O
10)I
11)R
12)W
1)C
2)
3)W
(Page 45):
nternal cleaning
eplacement of the lamp
ater level tank
iring diagram diagram of refrigeration unit
Maintenance manual
leaning the condenser (skilled personnel only)
Replacement of the cover's lifting motor
!
!
1.
2.
3.
4.
5.
WARNINGS
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety.
1
2
3
4
5
6
7
. Adults should operate this appliance only. Do not allow children to use the controls or play with it. . It
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
installation of the appliance should be carried out by a qualified electrician or other competent person.
. Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs.
. The manufacturers of this appliance accept no responsibility for the consequences of misuse in
contravention of these safety instructions. It further reserves the right to carry out improvements without
prior notice.
8
9
10
11
Our products are for internal use only
–
do not install outside restaurants, shops.
UNPACKING INSTRUCTIONS
1a.
CLEANING OF THE INTERNAL TANK
1
2
3.
DRIP TRAYS
1
2.
NOTICE:
. Avoid installing the cabinet directly in line with sunlight. . Nevere install the appliance near
sources of heat, such as radiators, stoves, etc.
. Keep the ventilation grills free from obstruction for at
least 30 cm.
. If damp air or products to be refrigerated should cause ice to form on the evaporator, we
recommend stopping the compressor and placing the goods in special refrigerated containers, kept at the
same temperature, until defrosting is completed;if this is not carried out the compressor will continue to
operate leading to a wasteful consumption of electricity and poor performance.
Cut surrounding tape. Remove the cardboard package by sliding it upwards, remove the nails from
. Remove the protection film from stainless steel parts. . Clean the tank with a soft sponge and neutral
detergents.
Remove the plastic caps from the drainage holes in the tank to drain off any residual water.
. Remove the protection film from the trays.
Mount the drip trays by resting them on the bottom of the
tank.
For Fishing models, start with the first shelf, positioned centrally, with no holes and with a
central slot
the wooden crate with care. . Insert forks of forklift truck between the appliance and pallet or crate.
Lift
the appliance.
Remove the pallet or crate. . Place the appliance on a flat, level surface.
Make sure
there is nothing left in the package before disposing of it. . Sort out the packaging materials in order to
facilitate disposal. . The appliance can be locked in place by engaging the wheel brakes (see picture 1).
. Unpack the glass panels. . Insert the glass side panels in the special U-brackets you will find in the
upper section of the cabinet (see picture 4). . Tighten the brackets' screws.
Having assembled both
glass panels, insert the steel ceiling lamp assembly. . Fix the lamp assembly with the screws supplied.
Protect the lamp cables with the profiles provided. . Assemble the front panel, inserting it into its seat
(see figure 5).
Plug the machine into the power supply socket. . Turn the switch of the electric lifting system (A) to
position II until the cover is fully
Never use detergents containing alcohol or solvents which would irremediably damage the cover,
compromising its transparency. . Use only a soft damp sponge. . As far as the wooden surfaces are
concerned, use proprietary detergents especially designed for wooden surfaces, which are water-based
and do not contain solvents. . Dry with a clean cloth.
(see picture 8).
2
3.
4.
5
6.
7
8
GLASS ASSEMBLY
1
2
3
4.
5
6.
7
OPENING THE PROTECTIVE COVER
1.
2
CLEANING THE COVER AND EXTERNAL PARTS
1.
2
3
4
6.
