Team SILK AXL012 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 68

background image

SX012/AXL012 Flange Facing and Grooving Machine

29

5.3.2 Starting the machine - Facing and Grooving

1. Set up the tool, refer to Section 5.2.4.

2. Select the cutting feed traverse, refer to Section 5.2.5.

3. Position the tool over the cutting area.

4. Set depth of cut on the toolpost feed knob.

5. Select the desired feed rate; refer to Fig. 3 and Table 1.

6. Engage the auto feed to the up position.

WARNING: THE MACHINE HAS DANGEROUS MOVING PARTS WHEN

OPERATED, THEREFORE KEEP WELL CLEAR.

SHOULD THE AIR SUPPLY FAIL FOR ANY REASON, THE OPERATOR MUST

SHUT THE AIR CONTROL VALVE SO THAT IT LOCKS IN THE CLOSED

POSITION UNTIL THE AIR SUPPLY HAS BEEN RESTORED.

7. Start the machine by opening the air control valve, refer to Section 5.3.1.

WARNING: DO NOT ATTEMPT TO MAKE ADJUSTMENTS WHILE THE

MACHINE IS OPERATING. ALWAYS STOP THE MACHINE FIRST.

If the cutting feed or direction of the machine is to be changed, the machine must

be stopped and the appropriate feed/direction selected. The machine can then be

restarted.

Now the machine is ready to use the operator can adjust any one of the following

variables:

a. depth of cut
b. tool profile
c. automatic traverse, on or off
d. rate and direction of feed

«
...
28
29
30
31
32
...
»

Содержание SILK AXL012





































































Отзывы:

Нет отзывов

Похожие инструкции для SILK AXL012

Бренд: Waterwise Страницы: 12

Бренд: ParaBody Страницы: 38

Бренд: KaVo Страницы: 13

Бренд: vc999 Страницы: 52

WJHD309 - DIGITAL DISK RECORDER

Бренд: Panasonic Страницы: 7

WJ-ND300 Administrator Console

Бренд: Panasonic Страницы: 24

Бренд: Parr Instrument Страницы: 24

Бренд: JBL Страницы: 15

Бренд: T-Rex Страницы: 13

Бренд: WalkMed Страницы: 2

Бренд: Walinga Страницы: 20

Бренд: Life Fitness Страницы: 45

VADA TWIN MOTOR MACERATOR

Бренд: Reece Страницы: 7

Бренд: Parkside Страницы: 37

Бренд: York Fitness Страницы: 18

Бренд: 4B Страницы: 16

Бренд: FitEngine Страницы: 68

Бренд: olympia electronics Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды