Team SILK AXL012 Скачать руководство пользователя страница 14

Страница: 14 / 68

SX012/AXL012 Flange Facing and Grooving Machine

SECTION 3 SAFETY INFORMATION

3.1 WARNINGS AND CAUTIONS

GENERAL:

ALL SAFETY PROCEDURES MUST BE OBSERVED AND STRICTLY

ADHERED TO WHEN INSTALLING, USING, MAINTAINING AND

SERVICING THIS EQUIPMENT.
ONLY TRAINED AND COMPETENT PERSONNEL SHOULD INSTALL,

USE, MAINTAIN AND SERVICE THIS EQUIPMENT.
ENSURE AN EMERGENCY STOP IS ALWAYS WITHIN REACH OF THE

OPERATOR.

INTENDED USE OF THIS EQUIPMENT:

THIS EQUIPMENT IS FOR USE BY PROFESSIONAL, TRAINED

PERSONNEL WORKING IN AN INDUSTRIAL ENVIRONMENT.
THIS EQUIPMENT IS INTENDED FOR USE ON METALS AND

ANALOGOUS SUBSTANCES.
THIS EQUIPMENT IS NOT INTENDED FOR USE ON WOOD, PLASTIC OR

SIMILAR ANALOGOUS SUBSTANCES.

USE OUTDOORS:

THIS EQUIPMENT SHOULD NOT BE USED DURING SEVERE WEATHER

CONDITIONS.
PERSONNEL SHOULD NOT OPERATE THIS EQUIPMENT IN WEATHER

CONDITIONS WHICH MAY GIVE RISE TO THE FOLLOWING:

- INADEQUATE VISIBILITY
- THE BUILD-UP OF ICE, SNOW, WATER, SAND OR DUST ON

PLATFORMS, LADDERS, CONTROLS, VISUAL INDICATORS,

MOVING PARTS, ETC.

- RISK OF INJURY DUE TO STRONG OR GUSTING WINDS

THIS EQUIPMENT SHOULD BE SUITABLY PROTECTED FROM ALL

SEVERE WEATHER CONDITIONS.

Содержание SILK AXL012





































































Результаты поиска

Содержание SILK AXL012

Отзывы:

Похожие инструкции для SILK AXL012

Бренды по названию

Популярные бренды

Team SILK AXL012, Инструкция по эксплуатации

Результаты поиска

Содержание SILK AXL012

Отзывы:

Похожие инструкции для SILK AXL012

Бренды по названию

Популярные бренды