Team SILK AXL012 Скачать руководство пользователя страница 35

Страница: 35 / 68

SX012/AXL012 Flange Facing and Grooving Machine

Periodic maintenance chart continued…

PERIOD

TASK

Returning to storage

Complete the daily, weekly and monthly tasks.

Protect all the exposed areas of the machine from

corrosion.

Annually when in storage

Un-pack the equipment and check for signs of

corrosion or other deterioration.

Check that all the components are present and in

good working order.

WARNINGS:

WHEN OILING AIR MOTORS WEAR FACE MASK TO AVOID INHALATION OF OIL MIST

AND FUMES.

DO NOT USE FLAMMABLE LIQUIDS TO LUBRICATE OR FLUSH THROUGH THE AIR

MOTOR. ONLY USE A RECOMMENDED AIR MOTOR LUBRICANT.

7.3 RECOMMENDED LUBRICANTS

These are the recommended lubricants for the SX012/AXL012 Flange Facing and Grooving

Machine.

Component

Lubricant type

Product name or specification

Air motor

Oil

Light machine oil

Motor gearbox

Grease

Moly-based

general

purpose

grease

Saddle

Grease

Moly-based

general

purpose

grease

Содержание SILK AXL012





































































Результаты поиска

Содержание SILK AXL012

Отзывы:

Похожие инструкции для SILK AXL012

Бренды по названию

Популярные бренды

Team SILK AXL012, Инструкция по эксплуатации

Результаты поиска

Содержание SILK AXL012

Отзывы:

Похожие инструкции для SILK AXL012

Бренды по названию

Популярные бренды