Team SILK AXL012 Скачать руководство пользователя страница 10

Страница: 10 / 68

SX012/AXL012 Flange Facing and Grooving Machine

TRAVERSE

SELECTOR LEVER

POSITION

FEED (mm per

revolution)

FEED (in per revolution)

COARSE (IN)

0.81 mm

0.032 in.

FINE (OUT)

0.20 mm

0.008 in.

Table 1 Feed rates

1.2.3 Gearbox

The gearbox is mounted on the drive assembly cover and transmits the drive from

the air motor through two bevel gears and an intermediate idler gear to the bearing

drive gear (spur ring gear).

1.2.4 Motor unit

The machine is driven by a 0.8 kW (1.07 hp) pneumatic motor with a free running

output speed of 382 rpm and incorporating an exhaust manifold and muffler.

The motor is attached to a motor flange with a bevel gear and bearing keyed and

secured to the motor spindle. The motor and flange assembly is attached to the

gearbox.

The AXL012 machine version is fitted with one motor and the SX012 version is

fitted with two motors.

1.2.5 Optional accessories

The following optional accessories are available upon request:

'V' groove machining kit
'V' groove measuring kit
Lens ring machining and polishing kit

Содержание SILK AXL012





































































Результаты поиска

Содержание SILK AXL012

Отзывы:

Похожие инструкции для SILK AXL012

Бренды по названию

Популярные бренды

Team SILK AXL012, Инструкция по эксплуатации

Результаты поиска

Содержание SILK AXL012

Отзывы:

Похожие инструкции для SILK AXL012

Бренды по названию

Популярные бренды