Team SILK AXL012 Скачать руководство пользователя страница 8

Страница: 8 / 68

SX012/AXL012 Flange Facing and Grooving Machine

SECTION 1 TECHNICAL DESCRIPTION

1.1 INTRODUCTION

The TEAM

SX012/AXL012 Flange Facing and Grooving Machine is constructed from the

highest quality materials and great care has been taken in its design and manufacture. Its

design will give every satisfaction provided that it is properly installed, operated and

maintained in accordance with the information contained within this manual.

Take care of this manual; it is an essential source of information.

1.2 EQUIPMENT DESCRIPTION

The purpose of the TEAM

SX012/AXL012 flange facing and grooving machine is designed

to machine full faced, raised face and grooved flanges up to 300 mm (11.750") in diameter,

at any location having a minimum pneumatic air supply 1.6 m

/m, 6 bar (60 cfm,87 psi).

The machine can achieve a variety of surface finishes from 6.3 µm Ra to 1.6 µm Ra when

turning and 1.6 µm Ra to 0.8 µm Ra when polishing. The machine can also produce a

'gramophone' finish, 'O' ring grooves and 'V' grooves, and alternatively lens ring facings.

The machine consists of four main assemblies (see Fig.1):

a.  Drive ring and bearing assembly
b.  Saddle
c.  Gearbox
d.  Motor unit

The machine is available as either a single motor AXL012 or a twin motor SX012 version.

The function and operation of these variants are identical.

1.2.1 Drive ring and bearing assembly

The drive and bearing assembly forms the main body of the machine which

comprises two main sub-assemblies: the drive assembly and the spur ring gear.

The drive assembly

The drive assembly, which is the fixed part of the machine, has four base clamp

blocks bolted to the base plate on the underside, and two flanges for mounting the

drive gearboxes.

The drive assembly houses an idler gear, which transfers the drive from the

gearbox to the spur ring gear. A cross-roller bearing assembly is clamped between

the drive assembly and the base plate, and the inner (rotating) race is clamped to

the spur ring.

Содержание SILK AXL012





































































Результаты поиска

Содержание SILK AXL012

Отзывы:

Похожие инструкции для SILK AXL012

Бренды по названию

Популярные бренды

Team SILK AXL012, Инструкция по эксплуатации

Результаты поиска

Содержание SILK AXL012

Отзывы:

Похожие инструкции для SILK AXL012

Бренды по названию

Популярные бренды