TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 18

Страница: 18 / 67

HGP Kit Manual

4.0 Installation

Table 7 – 600 V, 60Hz, HGP

HGP Rating (HP)

Tuned Circuit Current (A) Line Current (A)

1.8

6.1

7.5

4.1

6.8

8.2

10.9

13.7

20.5

27.4

34.2

100

41.0

125

54.7

125

150

61.6

144

200

82.1

192

250

103

242

300

123

289

350

144

336

400

164

382

450

185

412

500

205

472

600

246

576

700

287

672

800

328

780

900

369

864

1000

410

960

KDR Line Reactor Installation Instructions

Recommendations and Considerations

When installing the KDR Line Reactors on the INPUT side of the VFD, please use the following

guidelines when wiring the unit:

The KDR Line Reactor is a 3-phase device and should be wired in series and positioned on the input

side of the VFD.

All Terminal Block connectors will be marked. A1, B1, and C1 are the input terminals where the 3

phases of incoming power are to be wired. The tap for the filter connection will be marked AT, BT,

and CT. Output terminals will be marked A2, B2, and C2. Do not swap input and output terminals.

Units with copper bus or ring lug terminals are not marked. Wiring from the output terminals should

connect to the input of the VFD.

Refer to NEC (National Electrical Code) wiring practices for appropriate wire sizes for your application.

TCI recommends that these reactors be wired and located as close to the front end of the VFD as

possible to have the greatest success in both protecting the VFD as well as mitigating line harmonics.

We recommend this be 10 feet of cable or less.

Reactors generate a lot of heat in normal operations and their surfaces get very hot. In standard 40°C

ambient or less installations, a clearance of 3 inches on all sides of the reactors and its enclosure is

recommended for assisting in heat dissipation. This is a general guideline for typical applications. If

the reactor is being installed next to a heat sensitive instrument or control device, we recommend

Содержание HGP HarmonicGuard Series




































































Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды

TCi HGP HarmonicGuard Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды