TCi HGP HarmonicGuard Series Скачать руководство пользователя страница 11

Страница: 11 / 67

HGP Kit Manual

4.0 Installation

Make sure that the HGP kit is correct for the application. The voltage ratings of the filter kit must

match the input voltage rating of the connected drive. The horsepower and current ratings of the

filter kit must be appropriate for the connected load.

Technical Specifications

Table 1 - HarmonicGuard

Passive Filter Technical Specifications

Electrical Characteristics

Voltage Rating

208, 240, 380-415, 440, 480 or 600 VAC

Phase

Compliance

IEEE-519 2014

Operating Frequency

50 or 60 Hz

Motor drive input power rating range

1.5 – 1250 HP for 480V units. Power range varies

depending on system voltage.

Immunity from Voltage Distortion

Less than 5% THID at full load with THVD as high as

5%*

Overload Capability

200% of current rating for 3 minutes

Environmental Conditions

Operating Temperature

Kit component ambient: 50°C (122°F)

Storage Temperature

60°C (140°F)

Elevation

Up to 2,000 m without derating

Humidity

95% non-condensing

Agency approvals or certifications

Capacitor Assemblies

UL and cUL Listed

Capacitors

UR and cUR Recognized

Reactors

UR and cUR Recognized

Reactors

UL and cUL Listed

Performance Guarantee

To meet the requirements for the Performance Guarantee the minimum system conditions must

conform to the following:

•

No more than 1.5% Source inductance

•

The input VFD current waveform shall be consistent with that of a VFD with 3% AC line

reactance at full load

Please consult TCI regarding optimum filter performance when applied to DC drives.

4.0

Installation

Installation Guidelines

Installation Checklist

The following are the key points to be followed for a successful installation.

Make sure that the installation location will not be exposed to direct sunlight, corrosive

or combustible airborne contaminants, excessive dirt or liquids.

Select a mounting area that will allow adequate cooling air and maintenance access.

Содержание HGP HarmonicGuard Series




































































Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды

TCi HGP HarmonicGuard Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание HGP HarmonicGuard Series

Отзывы:

Похожие инструкции для HGP HarmonicGuard Series

Бренды по названию

Популярные бренды