1-10
INTRODUCTION
Models C712/C713
Introduction
1
•
Authorized service personnel must ensure that
the proper personal protective equipment (PPE)
is available and worn when required during
installation and service.
•
Authorized service personnel must remove all
metal jewelry, rings, and watches before
working on electrical equipment.
WARNING!
This machine has many sharp
edges that can cause severe injuries.
Examples:
•Scraper blades
•Condenser fins
•Cup/cone dispenser (if applicable)
Electrical Connections
IMPORTANT! In the United States, this
machine is intended to be installed in accordance with
the National Electrical Code (NEC), ANSI/NFPA 701987.
The purpose of the NEC code is the practical
safeguarding of persons and property from hazards
arising from the use of electricity. This code contains
provisions considered necessary for safety.
In all other areas of the world, the machine should be
installed in accordance with the existing local codes.
Please contact your local authorities if you have any
questions.
Each machine requires one power supply for each data
label on the machine. Check the data label(s) on the
machine for branch circuit overcurrent protection or fuse,
circuit ampacity, and other electrical specifications.
See the wiring diagram provided inside the electrical box
for proper power connections.
WARNING!
This machine must be properly
grounded! Failure to do so can result in severe personal
injury from electrical shock!
IMPORTANT! This machine is provided with
an equipotential grounding lug that is to be properly
attached to the rear of the frame by the authorized
installer. The installation location is marked by the
equipotential bonding symbol (5021 of IEC 60417-1) on
the removable panel and the frame.
WARNING!
Avoid injury.
•
DO NOT
attempt any repairs unless the main
power supply to the machine has been
disconnected.
•
DO NOT
operate the machine with larger fuses
than specified on the data label.
•
Stationary machines which are not equipped
with a power cord and plug or other device to
disconnect the machine from the power source
must have an all-pole disconnecting device with
a contact gap of at least 0.125 in. (3 mm)
installed in the external installation.
•
Machines that are permanently connected to
fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected,
not used for long periods, or during initial
installation, shall have protective devices to
protect against the leakage of current, such as a
GFI, and be installed by authorized personnel to
the local codes.
•
Supply cords used with this machine shall be
oil-resistant, sheathed flexible cable, not lighter
than ordinary polychloroprene or other
equivalent synthetic elastomer-sheathed cord
(code designation 60245 IEC 57) installed with
the proper cord anchorage to relieve conductors
from strain, including twisting, at the terminals
and protect the insulation of the conductors
from abrasion.
•
For Cord-Connected Machines:
Only
authorized Taylor service technicians may
install a plug on this machine.
Failure to follow these instructions may result in
electrocution or equipment damage.
!
FOLLOW YOUR LOCAL ELECTRICAL CODES.
Содержание C712
