INTRODUCTION
1-9
Models C712/C713
Introduction
1
General Installation Instructions
NOTICE!
Only trained, authorized service technicians
should install this machine. Failure to comply will void the
factory warranty.
The following are general installation instructions. For
complete installation details, please see the checkout
card.
IMPORTANT! All wiring and plumbing must
conform to national and local codes.
Site Preparation
Review the area where the machine is to be installed
before uncrating the machine. Make sure that all possible
hazards to the user and the equipment have been
addressed.
Clearance: Air-Cooled Machines
This machine requires a minimum of 3 in. (76 mm) air
clearance around all sides.
DO NOT
obstruct air intake and discharge openings.
Install the deflector provided to prevent recirculation of
warm air.
Failure to allow proper clearance and airflow may cause
poor freezer performance and damage to the machine.
For Indoor Use Only:
This machine is designed to
operate indoors, under normal ambient temperatures of
70°F to 75°F (21°C to 24°C). The freezer has
successfully performed in high ambient temperatures of
104°F (40°C) at reduced capacities.
WARNING!
This machine must
NOT
be
installed in an area where a water jet or hose can be
used. Never use a water jet or hose to rinse or clean this
machine. Using a water jet or hose on or around this
machine may result in the electrocution of the user or
damage to the machine.
CAUTION!
This machine must be installed on
a level surface to avoid the hazard of tipping. Extreme
care should be taken in moving this machine for any
reason. Two or more persons are required to safely move
this machine. Failure to comply may result in personal
injury or machine damage.
Uncrate the machine. Inspect the machine for damage.
Report any damage to the Taylor factory immediately.
This machine is made in the USA and has USA sizes of
hardware. All metric conversions are
approximate and vary in size.
Installer Safety
IMPORTANT! In all areas of the world, the
machine should be installed in accordance with existing
local codes. Please contact your local authorities if you
have any questions.
Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and service
of Taylor machines.
•
Only authorized Taylor service personnel should
perform installation and repairs on the machine.
•
Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the industry
standards on lockout/tagout procedures before
beginning any installation or repairs.
!
!
INSTALL POTABLE WATER CONNECTION
WITH ADEQUATE BACKFLOW
PROTECTION TO COMPLY WITH
APPLICABLE FEDERAL, STATE, AND
LOCAL CODES.
!
Содержание C712
