Taylor C712 Скачать руководство пользователя страница 47

Страница: 47 / 120

CONTROLS

2-25

Models C712/C713

Controls

C712/C713 UVC4 Update Instructions

Estimated Time: 35 minutes

Important!

•

See “UVC4 Electrostatic Discharge and Proper

Handling Procedures” on page 2-22 before han-

dling a UVC4 board.

•

Before performing software update, reset the

control to defaults. This will clear the RAM mem-

ory so the new software can be loaded.

•

Only use factory supplied USB drives to perform

software update. Do not make copies of factory

supplied USB drives with generic USB drives.

Failure to follow this instruction can cause

issues in successfully completing the software

update.

•

Wear appropriate personal protective

equipment.

1. Enter the Service menu (5231) to copy the current

machine settings.

2. Place both sides of the machine in the OFF mode

and turn the syrup heaters off.

CAUTION!

Disconnect all power to the

machine. Failure to follow this instruction may result in
electrocution.

4. Remove the two drip trays from the upper rear of the

machine and place them on top of the machine.

5. Remove the two screws at the bottom of the



Panel-Rear-Upper.

6. Remove the six screws from the Cover-Control Box.

7. Install a jumper on the W2 on the left side interface

board.

8. Reconnect power to the machine and turn power on.

Verify that the display says UNIT CLEANED.

9. Remove the jumper from W2 on the left side interface

board.

10. Enter the Service Menu and go to the option, Reset

to Defaults.

11. Perform a Reset to Defaults by selecting YES to

clear all RAM memory.

12. Install the USB flash drive in the J4 port on the UVC4

board.

13. Check jumper position JP7. Remove the jumper, if

present, and do not reinstall.

14. Access the Service Menu. Go to Software Update

and select YES to begin update process.

15. Wait 3 minutes for the software to complete the

update.

16. After the Lamp Test, enter the Service Menu and

clear any faults. Reset unit to defaults.

17. Re-enter all settings copied earlier.

18. Remove the USB flash drive from the UVC4 board

and store it in the tool kit.

19. Place both sides of the unit in the Auto mode. Turn

the syrup heaters back on, if that was the original
state before the installation.

20. Verify both sides of the machine are operating

properly (shutting off at proper viscosity and no
faults).

21. Draw at least one soft serve cone per side to verify

that the product appearance is acceptable

22. Carefully reinstall the control box cover, back panel,

and drip trays.

Содержание C712

























































































































Результаты поиска

Содержание C712

Отзывы:

Похожие инструкции для C712

Бренды по названию

Популярные бренды

Taylor C712, Руководство по обслуживанию

Результаты поиска

Содержание C712

Отзывы:

Похожие инструкции для C712

Бренды по названию

Популярные бренды