manualshive.com logo in svg

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 85 / 204

Поделиться
Скачать
Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 85

Maintenance, Service, and Repair

Suspension

Page 3

Leaf

If a spring has failed or is fatigued, then it is
recommended that both front springs are replaced as a
set.

HINT : In most vehicles it will be easier if the springs

are replaced one at a time.

6. Raise the front of the vehicle and support with

jack stands.

7. Tie up or support the front axle so it cannot fall

out of the vehicle.

8. Unbolt the spring from the front axle beam.

9. Support the spring so that it cannot fall out of the

vehicle.

10. Remove the lower bolt from the spring hanger.

11. Remove the spring bolt from the other end of the

spring and remove the spring from the vehicle.

12. Inspect the spring bolts and spring hangers for

signs of wear or damage. If any wear or damage
is found, then they must be replaced.

13. Install the new spring in reverse order.

REPLACE THE FRONT
SPRINGS

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Set the park brake.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

Damaged or worn spring bolts or hangers

could result in sudden failure of the

suspension causing severe bodily injury or

property damage.

14. If the spring hanger bolts do not have a grease

fitting, lube the spring bushings before installing
the spring.

15. Torque the spring hanger bolts to 20 ft-lbs.

16. If the spring bolts are equipped with grease fittings,

lube them at this time.

17. Lower the vehicle.

18. Reconnect the main positive and negative cables

at the batteries.

19. Remove the blocks from behind the wheels.

20. Release the parking brake and test drive the

vehicle.

Содержание B0-248-TT













































































































































































































Отзывы:

Нет отзывов