Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 22

Страница: 22 / 204

SAFETY RULES AND OPERATING INSTRUCTIONS

Safety Rules
Page 8

Parking

Before leaving the vehicle:

•

Set the parking brake.

•

Set the forward-off-reverse switch to the ` “OFF”
position.

•

Rotate the start switch to the “OFF” position.

In addition:

•

If parking this vehicle on an incline, turn the wheels
to the curb, or block the wheels.

•

Do not block fire aisles, emergency equipment,
stairways, or exits.

This vehicle is equipped with regenerative

braking. Follow these steps before towing

this vehicle.
1. To tow this vehicle the start switch must

be in the “OFF” position.
2. Place the forward/reverse switch in the

center “OFF” position.
Failure to follow these instructions may

result in damage to the vehicle.

The park brake should be disabled for

servicing or towing procedures only. Do not

operate the vehicle while the automatic

park brake is disabled. Operating the

vehicle with the automatic park brake

disabled could lead to severe bodily injury

and/or property damage.

Towing This Vehicle

To tow this vehicle, attach a tow strap to the front bumper
tow-bar.

NOTE: If the vehicle is equipped with an automatic

electric brake, do not tow the vehicle with
the drive wheels on the ground.

Use another driver to steer this vehicle while it is being
towed. Be sure the driver uses the brakes when the
towing vehicle slows or stops. Do not tow the vehicle
faster than 5 m.p.h. or its maximum designed speed,
whichever is lower.

If at all possible, this vehicle should be placed on a carrier,
rather than towing.

Содержание B0-248-TT













































































































































































































Результаты поиска

Содержание B0-248-TT

Отзывы:

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 22 / 204

Результаты поиска

Содержание B0-248-TT

Отзывы: