manualshive.com logo in svg

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 76 / 204

Поделиться
Скачать
Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 76

Maintenance, Service, and Repair

F2/F3 Transmission
Page 6

Assemble

1. Thoroughly clean all gasket surfaces.

2. Apply a 1/8” bead of 94-430-03 gasket sealer to

the face of the 3rd member.

3. Install the backing plate to the 3rd member. Torque

to 30-45 ft-lbs.

4. Install the motor to the backing plate. Do not fully

tighten the motor mounting hardware at this time.

5. Install the motor sprocket, drive sprocket and

chain. Do not adjust the chain tension at this time.

6. Apply a 1/8” bead of 94-430-03 gasket sealer to

the chain case housing.

7. Install the chain case centering tool (refer to

Appendix A)  into the pinion seal bore in the chain
case housing.

CHAIN CASE

NOTE: Some vehicle configurations may require that

the transmission be removed to disassemble
the chain case. Refer to section

Transmission Assembly

 for information

on removing the transmission.

Disassemble

6. Place an oil drain pan under the chain case.

7. Remove the chain case drain plug and allow all of

the oil to drain from the housing and then reinstall
the drain plug

8. Remove the brake drum. Refer to section

Brakes: Replace the Brake Drum

 for

information regarding removing the brake drum.

9. Remove the nuts from the three threaded studs at

the small end of the chain case housing.

10. Remove the chain case housing bolts, brake

assembly, and alignment brackets.

11. Remove the chain case housing from the backing

plate.

12. Remove the pinion seal from the chain case

housing.

13. Loosen the motor mounting bolts.

14. Loosen the chain adjuster.

15. Remove the drive chain, motor nut and sprocket

and the drive sprocket.

16. If the backing plate must be removed from the

3rd member, first remove the motor from the
backing plate then remove the backing plate from
the 3rd member.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Set the park brake.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Typical Chain Case

Apply sealer around the ID of the holes

Содержание B0-248-TT













































































































































































































Отзывы:

Нет отзывов