manualshive.com logo in svg

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 62 / 204

Поделиться
Скачать
Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 62

Maintenance, Service, and Repair

Brakes
Page 10

REPLACE THE WHEEL
CYLINDER

Disc Brake Body Assembly (front or rear)

6. Release the park brake.

7. Raise the wheel off of the ground and support with

jack stands.

8. Remove the tire/wheel assembly. Refer to 

Tires

and Wheels

 section for information on removing

the tire and wheel assembly.

9. Thoroughly clean the area around the brake body.

10. Remove the brake body bolts and discard the lock

nuts.

11. Inspect the brake rotor. Refer to 

Inspect the

Service Brake

 section for information regarding

inspecting the brake rotor.

12. Disconnect the brake hose from the brake body.

13. Install the new brake body assembly in reverse

order.

•

Use teflon tape thread sealant on the brake hose
fitting.

•

Torque the brake body bolts to 11 ft-lbs.

14. Bleed the brakes. Refer to 

Bleed the Brakes

section for information regarding bleeding the
brakes.

Current Taylor-Dunn

®

 brakes are asbestos

free. However, there is the possibility that

the original brakes were replaced with

aftermarket parts containing asbestos.

Since this possibility exists, all brake parts

should be handled as if they contain

asbestos. Refer to Appendix C for

recommended handling precautions.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

15. Set the park brake.

16. Reconnect the main positive and negative cables

at the batteries.

17. Lower the wheel to the ground.

18. Remove the blocks from behind the wheels.

19. Release the park brake and test drive the vehicle.

Do not ingest brake fluid or allow contact

with skin or eyes. Always wear protective

clothing and a face shield when working

with or around brake fluid.
SKIN CONTACT
Flush area immediately with water for

several minutes. If a rash or skin irritation

develops, get medical attention

immediately.
EYE CONTACT
Immediately flush the eye with water for

15 minutes and call physician.
INGESTION
Get medical attention immediately.

Содержание B0-248-TT













































































































































































































Отзывы:

Нет отзывов