Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 204

Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 32

Maintenance, Service, and Repair

Front Axle
Page 2

INSPECT THE FRONT WHEEL BEARINGS AND KING PIN

6. Raise the front of the vehicle and support with

jack stands.

7. Grab the top and bottom of the tire/wheel

assembly. Feel for any movement or play while
pulling and pushing on the top and bottom of the
tire. Any movement or play is an indication of loose
wheel bearings or king pin.

NOTE: Refer to the

Adjust Front Wheel Bearings

section for information regarding the
adjustment of the wheel bearings.

NOTE: If the king pin is loose, then refer to

Replace

the King Pins and Bushings

for

information regarding replacing the king pin
bushings. There are no adjustments for the
king pin or bushings.

1. Make sure the key-switch is in the “OFF” position, then remove the key.
2. Place the forward-reverse switch in the center “OFF” position.
3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to prevent vehicle movement.
5. Disconnect the main positive and negative cables at the batteries.

Always use a lifting strap, hoist, and jack stands, of adequate capacity to lift and support the

vehicle. Failure to use lifting and support devices of rated load capacity may result in severe

bodily injury.

8. Spin the wheel and listen for any grinding noise.

Any grinding noise may be an indication of worn
or damaged wheel bearings.

NOTE: Refer to the

Replace Front Wheel

Bearings

section for information regarding

the replacement of the wheel bearings.

9. Lower the vehicle.

10. Reconnect the main positive and negative cables

at the batteries.

11. Remove the blocks from behind the wheels.

12. Release the park brake and test drive the vehicle.

«
...
30
31
32
33
34
...
»

Содержание B0-248-TT













































































































































































































Отзывы:

Нет отзывов