manualshive.com logo in svg

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 34 / 204

Поделиться
Скачать
Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 34

Maintenance, Service, and Repair

Front Axle
Page 4

FRONT AXLE REMOVAL AND
INSTALLATION

Removal

6. Raise the front of the vehicle and support with

jack stands.

7. Remove both front wheels. Refer to 

Tires and

Wheels

 section for information regarding

removing the front wheels.

8. Tie up or support the front axle so it can not fall

out of the vehicle.

9. Disconnect the drag link ball joint or rod end from

the steering knuckle or the steering gear pitman
arm.

NOTE: Refer to the 

Replacing the Ball Joints

section for information regarding the removal
of the ball joints or rod ends.

10. If equipped with front brakes, disconnect the

hydraulic brake lines from the brake bodies.

11. Disconnect the front axle beam from the front

springs and remove the axle from the vehicle.

NOTE: In some configurations the front springs and

or shocks will have to be removed in order to
remove the axle beam. Refer to section

Front Suspension

 for information

regarding removing the springs and shocks.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Installation

6. Raise the front of the vehicle and support with

jack stands.

7. Install the front axle in reverse order of removal.

NOTE: Use all new cotter pins.

NOTE: Refer to the 

Replacing the Ball Joints

section for information regarding the installing
the ball joints or rod ends.

NOTE: Refer to 

Tires and Wheels

 section for

information regarding removing the front
wheels.

8. Realign the front wheels. Refer to 

Steering

Component Service 

section for information

regarding realigning the front wheels.

9. If equipped with front brakes, bleed the brakes.

Refer to 

Brake Service

 section for information

regarding bleeding the brakes.

10. Lower the vehicle.

11. Reconnect the main positive and negative cables

at the batteries.

12. Remove the blocks from behind the wheels.

13. Release the park brake and test drive the vehicle.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Содержание B0-248-TT













































































































































































































Отзывы:

Нет отзывов