Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 36

Страница: 36 / 204

Maintenance, Service, and Repair

Front Axle
Page 6

REPLACE FRONT WHEEL
BEARINGS

6. Raise the front of the vehicle and support with

jack stands.

7. Remove the tire/wheel assembly from the hub.

Refer to

Tires and Wheels

for information

regarding removing the wheel assembly.

8. Remove the hub dust cap, cotter pin, and spindle

nut.

9. Remove the hub from the steering knuckle.

NOTE: For a front disc brake option you must remove

the brake body before removing the hub.
Refer to the

Brakes

section for information

regarding the removal of the brake body.

NOTE: Catch the outer bearing as it falls out.

10. Thoroughly clean all grease from the inside of the

hub and the bearings.

11. Inspect and replace the races, bearings, and seals.

NOTE: It is recommended to replace all four bearings

and races in the left and right wheels as a
set.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

12. Assemble in reverse order, using new grease

seals.

NOTE: Refer to

Adjust Wheel Bearings

for

information regarding proper tightening of the
spindle nut

13. Install the hub dust cap.

14. Reinstall the brake body and the tire/wheel

assembly.

NOTE: Refer to the

Brakes

for information regarding

the installation of the brake body.

15. Lower the vehicle.

16. Reconnect the main positive and negative cables

at the batteries.

17. Remove the blocks from behind the wheels.

18. Release the park brake and test drive the vehicle.

Содержание B0-248-TT













































































































































































































Результаты поиска

Содержание B0-248-TT

Отзывы:

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 36 / 204

Результаты поиска

Содержание B0-248-TT

Отзывы: