Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 61

Страница: 61 / 204

Maintenance, Service, and Repair

Brakes

Page 9

NOTE: It is recommended that both the left and right

brake pads be replaced as a set.

NOTE: Installing new brake pads will raise the brake

fluid level in the master cylinder.

6. Thoroughly clean the area around the master

cylinder cap.

7. Remove fluid from the master cylinder until it is 1/

2 full.

8. Raise the rear of the vehicle and support with jack

stands.

9. Remove the tire/wheel assembly.

NOTE: Refer to

Tires and Wheels

section for

information on removing the tire and wheel
assembly.

10. Release the park brake (wheel brake only).

11. Remove the brake body bolts and discard the lock

nuts and brake pads.

12. Remove the spacer bushings from the mounting

bracket and discard.

13. Inspect the brake rotor. Refer to

Inspect the

Service Brake

section for information regarding

inspecting the brake rotor.

REPLACE REAR BRAKE PADS OR SHOES

Current Taylor-Dunn

brakes are asbestos

free. However, there is the possibility that

the original brakes were replaced with

aftermarket parts containing asbestos.

Since this possibility exists, all brake parts

should be handled as if they contain

asbestos. Refer to Appendix C for

recommended handling precautions.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

14. Inspect the spacers and replace if any wear or

damage is found.

15. Install new spacer bushings in the mounting

bracket.

16. Back off the parking brake adjustment (wheel park

brake only).

17. Install new brake pads in reverse order. Torque

the mounting bolts to 11 ft-lbs.

18. Repeat this procedure for the other wheel.

19. Install the tire/wheel assembly and lower the

vehicle to the ground.

20. Fill the master cylinder to the proper level. Refer

Check Master Cylinder Fluid

section for

information regarding the correct master cylinder
fluid level.

21. Adjust the parking brake (wheel park brake only).

Refer to

Adjust the Parking Brake

section.

22. Set the park brake.

23. Reconnect the main positive and negative cables

at the batteries.

24. Remove the blocks from behind the wheels.

25. Release the park brake and test drive the vehicle.

Содержание B0-248-TT













































































































































































































Результаты поиска

Содержание B0-248-TT

Отзывы:

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 61 / 204

Результаты поиска

Содержание B0-248-TT

Отзывы: