Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 38

Страница: 38 / 204

Maintenance, Service, and Repair

Front Axle
Page 8

REPLACE THE STEERING
KNUCKLE

6. Raise the front of the vehicle and support with

jack stands.

7. Remove the tire/wheel assembly. Refer to

Tires

and Wheels

section for information regarding

removing the tire/wheel assembly.

8. Remove the hub bearing cap, cotter pin and nut,

then remove the hub from the steering knuckle.

NOTE: For a front disc brake option you must remove

the brake body before removing the hub.
Refer to the

Brakes

section for information

regarding the removal of the brake body. Do
not remove the hydraulic brake line from the
brake body. If the brake line is removed then
it will be necessary to bleed the brakes.

NOTE: Catch the outer bearing as it falls out.

9. Remove the drag link and/or tie rod from the

steering knuckle. Refer to

Replace the Ball

Joints, Tie Rods, Drag Link

in this section for

information regarding removal of the drag link or
tie rod.

10. While supporting the knuckle, remove the king pin

and thrust bearing.

11. Remove the knuckle from the axle.

12. Thoroughly clean and/or replace all bearings, nuts,

washers, and bushings.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

NOTE: Both the left and right side bushings and thrust

bearings should be replaced as a set.

13. Assemble in reverse order. Refer to the

illustratinon below for orientation of the thrust
bearing.

14. Pack the thrust bearing with grease.

15. Tighten the king pin nut until all of the up and down

play is removed and the yoke rotates freely. The
rubber washer must compress slightly to create a
seal for the grease.

NOTE: Refer to

Adjust Wheel Bearings

for

information regarding proper tightening of the
spindle nut

16. Install new cotter pins.

17. Realign the wheels.

NOTE: Refer to the

Steering

section for information

regarding realignment of the front wheels.

18. Lower the vehicle.

19. Reconnect the main positive and negative cables

at the batteries.

20. Remove the blocks from behind the wheels.

21. Release the park brake and test drive the vehicle.

Содержание B0-248-TT













































































































































































































Результаты поиска

Содержание B0-248-TT

Отзывы:

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 38 / 204

Результаты поиска

Содержание B0-248-TT

Отзывы: