manualshive.com logo in svg

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 65 / 204

Поделиться
Скачать
Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 65

Maintenance, Service, and Repair

Brakes

Page 13

Push Rod

Plunger

Master Cylinder

1/8"

Cutaway of typical master

cylinder showing the push rod

REPLACE THE MASTER
CYLINDER

NOTE: Most vehicle configurations do not require

lifting the vehicle to remove the master
cylinder. Lifting the vehicle may not be
required.

6. If required, raise the vehicle and support with jack

stands.

7. Place a drain pan under the master cylinder.

8. Disconnect the brake line(s) to the master cylinder

and pump out the fluid in the master cylinder by
depressing the pedal several times.

9. Remove the master cylinder bolts and remove the

master cylinder from the vehicle.

10. Install in reverse order.

11. Adjust the master cylinder push rod so that it is

approximately 1/8 inch away from the master
cylinder plunger when the brake pedal is up.

12. Fill the master cylinder with brake fluid from a

sealed container.

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Confirm the electric park brake is set.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

Always use a lifting strap, hoist, and jack

stands, of adequate capacity to lift and

support the vehicle. Failure to use lifting

and support devices of rated load capacity

may result in severe bodily injury.

Do not ingest brake fluid or allow contact

with skin or eyes. Always wear protective

clothing and a face shield when working

with or around brake fluid.
SKIN CONTACT
Flush area immediately with water for

several minutes. If a rash or skin irritation

develops, get medical attention

immediately.
EYE CONTACT
Immediately flush the eye with water for

15 minutes and call physician.
INGESTION
Get medical attention immediately.

13. Pump the brake pedal a short distance of one to

two inches until no bubbles are seen coming from
the inlet ports inside of the master cylinder
chamber.

14. If the vehicle was raised, lower it to the ground.

15. Bleed the brakes. refer to 

Bleed the Brakes

section for information regarding bleeding the
brakes.

16. Reconnect the main positive and negative cables

at the batteries.

17. Remove the blocks from behind the wheels.

18. Release the park brake and test drive the vehicle.

•

Only use the specified brake fluid as indicated on page 1 of this section from
a new sealed container.

•

DOT 3 brake fluid  is corrosive and will damage paint finishes.

•

Dispose of brake fluid in accordance with local state and federal regulations.

•

Read and follow all warnings on the brake fluid container.

Содержание B0-248-TT













































































































































































































Отзывы:

Нет отзывов