Taylor-Dunn B0-248-TT Скачать руководство пользователя страница 74

Страница: 74 / 204

Maintenance, Service, and Repair

F2/F3 Transmission
Page 4

DRIVE MOTOR

Remove

NOTE: In most cases it is not necessary to

disassemble the chain case to remove the
motor. If you find it necessary to disassemble
the chain case, refer to

Transmission

section for information regarding disassembly
of the chain case.

6. Remove the four motor wires.

7. Loosen the drive chain adjusting screw.

8. Remove the hardware holding the motor to the

chain case backing plate.

9. Lift the rear of the motor and rotate the motor so

that the motor mounting plate clears the two
threaded studs on the chain case backing plate
and remove the motor from the drive.

Install

1. Tie the chain up in position with mechanics wire

as shown.

2. Slip the motor sprocket under the chain and rotate

the motor so that the mounting plate goes into the
threaded studs and remove wire(s) holding the
chain.

Do not allow the wheels to rotate after the

motor has been removed. Allowing the

wheels to rotate may result in the drive

chain getting bound up with the drive

sprocket, locking up the transmission.

Should this happen, the chain may have to

1. Make sure the key-switch is in the “OFF”

position, then remove the key.

2. Place the forward-reverse switch in the

center “OFF” position.

3. Set the park brake.
4. Place blocks under the front wheels to

prevent vehicle movement.

5. Disconnect the main positive and

negative cables at the batteries.

3. Install the motor mounting hardware but do not

tighten until the chain adjustment is complete.

4. Adjust the drive chain. Refer to

Adjust the Drive

Chain

for information regarding adjusting the

drive chain.

5. Connect the motor wires.

6. Reconnect the main positive and negative at the

batteries, remove the blocks from the wheels, and
test drive.

Chain tied with mechanics wire

Содержание B0-248-TT













































































































































































































Результаты поиска

Содержание B0-248-TT

Отзывы:

Taylor-Dunn B0-248-TT, Руководство по эксплуатации, устранению неисправностей и замене запасных частей, Страница: 74 / 204

Результаты поиска

Содержание B0-248-TT

Отзывы: