Taylor-Dunn AN 171 Скачать руководство пользователя

Страница: 48 / 206

Maintenance, Service, and Repair

Brakes
Page 6

REPLACE BRAKE DRUM

NOTE: Some vehicle configurations do not allow

clearance to remove the brake drum while
the drive is in the vehicle. In this case the
drive must be removed to replace the brake
drum. Refer to

Transmission Section

for

information on removing the drive from the
vehicle.

6. Release the park brake.
7. Loosen the bolt(s) on the brake band alignment

bracket(s) and pivot them out of the way.

8. Remove the pinion nut and slide the brake drum

off of the pinion shaft.

9. Remove the pinion seal.
10. Lightly grease the new pinion seal and install using

the pinion seal installation tool (see appendix C).

11. Install the brake drum using a new pinion nut.

Torque the pinion nut to 170 ft-lbs.

12. Position the brake band alignment bracket(s) so

that the inner arm is 0.100” away from the brake

drum. Make certain that the alignment bracket

does not come into contact with the brake drum.

13. Adjust the alignment bracket adjusting bolt(s) to

0.050-0.100" away from the brake band and tighten

the jam nuts.

14. Adjust the park brake. Refer to

Adjust the

BandBrake

section for information regarding

adjusting the park brake.

15. Set the park brake.
16. Reconnect the main positive and negative cables

at the batteries.

17. Remove the blocks from behind the wheels.
18. Release the park brake and test drive the vehicle.

Inspect the pinion seal for any signs of misalignment. A misaligned

pinion seal could cause premature failure of the pinion seal and an

oil leak. This could result in property damage and/or severe bodily

injury.

Current Taylor-Dunn

brakes are asbestos free. However, there is the possibility that the original

brakes were replaced with aftermarket parts containing asbestos. Since this possibility exists,

all brake parts should be handled as if they contain asbestos. Refer to appendix C for

recommended handling precautions.

Содержание AN 171















































































































































































































Результаты поиска

Содержание AN 171

Отзывы:

Похожие инструкции для AN 171

Бренды по названию

Популярные бренды

Taylor-Dunn AN 171, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание AN 171

Отзывы:

Похожие инструкции для AN 171

Бренды по названию

Популярные бренды