background image

SAFETY RULES AND OPERATING INSTRUCTIONS

Safety Rules
Page 8

VEHICLE OPERATIONAL
GUIDELINES

Safety Guidelines

Only qualified and trained operators may drive this

vehicle.

Drive only on level surfaces or on surfaces having

an incline of no more than 10% (5.6 degrees).

Drive slowly when making a turn, especially if the

ground is wet or when driving on an incline.

This vehicle may overturn easily if turned sharply or

when driven at high speeds.

Observe all traffic regulations and speed limits.

Keep  all body parts (head, arms, legs) inside this

vehicle while it is moving.

Keep the vehicle under control at all times.

Yield right of way to pedestrians, ambulances, fire

trucks, or other vehicles in emergencies.

Do not overtake another vehicle at intersections, blind

spots, or other dangerous locations.

Do not drive over loose objects, holes, or bumps.

Yield right of way to pedestrians and emergencies

vehicles.

Stay in your driving lane under normal conditions,

maintaining a safe distance from all objects.

Keep a clear view ahead at all times.

Starting:

Perform  all necessary vehicle preparation steps,

inspections,  or maintenance before operating this

vehicle.

1. Make sure the forward-off-reverse witch is in the

center “OFF” position.

2. Depress the rear of the treadle to set the parking

brake.

3. Rotate the ON-OFF switch to the “ON” position.
4. Place the forward-off-reverse switch in the desired

direction of travel.

7. Slowly depress the front of the treadle.

While driving:

Slow down and sound the horn to warn pedestrians

or when approaching a corner or other intersection.

No reckless driving.

Do not drive this vehicle on steep inclines or where

prohibited.

Immediately report any accidents or vehicle problems

to a supervisor.

Loading and Unloading

Do  not carry more than the maximum number of

passengers allowed for this vehicle.

Do not exceed the cargo load capacity.

Do not load cargo that can fall off.

Be careful when handling cargo that is longer, wider,

or higher than this vehicle, be sure to properly secure

all  loads.

Towing Loads:

• Do not exceed the towing capacity of the tractor.
• Do not exceed the load capacity of the trailer. Refer

to  documentation supplied with your trailer for

information regarding load capacity of the trailer.

• Make sure all loads are securely tied down. Refer to

documentation  supplied with your trailer for

information regarding attaching loads to the trailer.

• Do not back up when towing more than one trailer.
• Drive slowly when towing loads with a high center of

gravity.

• When turning, be sure to allow for “corner cutting” of

the trailer.

• Allow  for longer stopping distances when towing

heavy loads.

• Allow  for longer stopping distances when driving

down a grade.

Содержание AN 171















































































































































































































Отзывы: