Taylor-Dunn AN 171 Скачать руководство пользователя страница 19

Страница: 19 / 206

SAFETY RULES AND OPERATING INSTRUCTIONS

Safety Rules

Page 7

Parking brake

The parking brake functions the same on boththe SC

159 and AN 171. Depress the rear of the treadle to set

the brake.

Charger Interlock

The charger interlock is designed to disable the vehicle from being driven while the AC charger cord is

plugged into a functioning power source.
NOTE: The interlock shown is mounted external of the charger. Some vehicles may have the interlock built

into the charger.

Foot Interlock Switch, SC 159 (optional)

A switch or pedal located under the driver's left foot

disables the power to the vehicle when it is released.

The switch or pedal must be depressed for the vehicle

to operate. Whenever the driver leaves the vehicle, the

driver should turn the key-switch off, place the forward-

off-reverse switch in the center “OFF” position, and set

the park brake.

Содержание AN 171















































































































































































































Результаты поиска

Содержание AN 171

Отзывы:

Бренды по названию

Популярные бренды

Taylor-Dunn AN 171, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание AN 171

Отзывы:

Бренды по названию

Популярные бренды