Taylor-Dunn AN 171 Скачать руководство пользователя

Страница: 100 / 206

Curtis PMC Troubleshooting

Page 6

Control Wire Inputs

The voltage shown is for illustration
only. The actual voltage may vary.

Positive

Main Battery

Solenoids are shown for reference

only. The type of solenoid in your
truck may look different

REV

FWD

ISO

FWD

REV

Solenoids are shown for reference
only. The type of solenoid in your

truck may look different

The voltage shown is for illustration
only. The actual voltage may vary.

Connect a voltmeter across the Solenoid Negative Buss Bar
and battery positive.

•

If the voltage is not at battery volts then check the

wiring to battery negative and the negative circuit

breaker. Stop trouble shooting here and repair the

problem. When the repair is completed, completely

retest the vehicle before lowering the drive wheels

to the ground.

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

The rear drive wheels may rotate during some of the following tests. Block the

front wheels, raise the rear drive wheels off the ground, and support the vehicle

with jack stands. Failure to do so may cause the vehicle to move and cause

severe bodily injury and/or property damage.
Rotating rear drive wheels are a potential hazard. Keep hands, arms, legs and

loose clothing away from the rear drive wheels while conducting tests. Failure

to do so may cause serious bodily injury.

Connect a voltmeter across the ISO solenoid coil terminals.

Close all interlock switches and turn the Key Switch
ON.
Depress the accelerator pedal to engage MS-1 only.

• If the voltage is not at battery volts then go to the

Key Switch

sequence.

• If the voltage is at battery volts and the ISO solenoid

does not pick up (click) then the ISO solenoid has

failed. Stop trouble shooting here and repair the

problem. When the repair is completed, completely

retest the vehicle before lowering the drive wheels

to the ground.

Note: Vehicles with Dana H12 transmission,
Forward solenoid is in the center.

Содержание AN 171















































































































































































































Результаты поиска

Содержание AN 171

Отзывы:

Похожие инструкции для AN 171

Бренды по названию

Популярные бренды

Taylor-Dunn AN 171, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание AN 171

Отзывы:

Похожие инструкции для AN 171

Бренды по названию

Популярные бренды