Taylor-Dunn AN 171 Скачать руководство пользователя страница 62

Страница: 62 / 206

Transmission

Page 2

ADJUST THE DRIVE CHAIN

NOTE: A small amount of oil may come out when the drive motor mounting

bolts are loosened.

6. Place a small oil drain pan under the chain case.
7. Loosen but do not remove the three drive motor

mounting nuts.

8. Loosen the adjusting screw jam nut.

1. Make sure the key-switch is in the “OFF” position, then remove

the key.

2. Place the forward-reverse switch in the center “OFF” position.
3. Set the park brake.
4. Place blocks under the front wheels to prevent vehicle movement.
5. Disconnect the main positive and negative cables at the batteries.

Always use a lifting strap, hoist, and jack stands, of adequate capacity

to lift and support the vehicle. Failure to use lifting and support devices

of rated load capacity may result in severe bodily injury.

9. Raise the drive wheels off of the ground.

10. Tie the vehicle in place so that it cannot move.

Tie the vehicle to an immovable object to prevent the vehicle from

moving in forward or reverse. Failure to securely tie the vehicle may

result in unexpected vehicle movement resulting in severe bodily

injury or property damage.

Содержание AN 171















































































































































































































Результаты поиска

Содержание AN 171

Отзывы:

Бренды по названию

Популярные бренды

Taylor-Dunn AN 171, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание AN 171

Отзывы:

Бренды по названию

Популярные бренды