Taylor-Dunn AN 171 Скачать руководство пользователя страница 102

Страница: 102 / 206

Curtis PMC Troubleshooting

Page 8

1. Make sure the key-switch is in the “OFF” position, then remove the key.

2. Place the forward-reverse switch in the center “OFF” position.

3. Set the park brake.

4. Place blocks under the front wheels to prevent vehicle movement.

The rear drive wheels may rotate during some of the following tests. Block the

front wheels, raise the rear drive wheels off the ground, and support the vehicle

with jack stands. Failure to do so may cause the vehicle to move and cause

severe bodily injury and/or property damage.
Rotating rear drive wheels are a potential hazard. Keep hands, arms, legs and

loose clothing away from the rear drive wheels while conducting tests. Failure

to do so may cause serious bodily injury.

Power Wire Inputs

Connect a voltmeter to the PMC ‘B-’ terminal and battery
positive.

• If the voltage is not the same as battery volts then

there is an open circuit in the wire from ‘B-’ to the

battery. Stop troubleshooting here and repair the

problem. When the repair is completed, completely

retest the vehicle before lowering the drive wheels

to the ground.

B-

M-

B+

KSI

Main Battery Positive

The voltage shown is for illustration
only. The actual voltage may vary.

B-

M-

B+

KSI

The voltage shown is for illustration
only. The actual voltage may vary.

Connect a voltmeter across the PMC ‘B-’ terminal and the
PMC ‘B+’ terminal.

Close all interlock switches, turn the Key Switch ON,
and place the F&R Switch in Forward.
Depress the accelerator pedal to engage MS-1 only.

•

If the voltage is not the same as battery volts then

go to the

Solenoids

sequence.

•

If the voltage is the same as battery volts then the

PMC controller has failed. Stop trouble shooting

here and repair the problem. When the repair is

completed, completely retest the vehicle before

lowering the drive wheels to the ground.

Содержание AN 171















































































































































































































Результаты поиска

Содержание AN 171

Отзывы:

Бренды по названию

Популярные бренды

Taylor-Dunn AN 171, Руководство по эксплуатации, устранению неисправностей и замене запасных частей

Результаты поиска

Содержание AN 171

Отзывы:

Бренды по названию

Популярные бренды